4 WIRINGConnection method Insert the cable with connector CN-66A-Cinto the product’s connector area for a power Disconnection method Pressing the release lever of the cable withCable with connectorCN-66A-CReleaseleverConnector area of the cable withconnectorHousing: PAP-06V-S!"#$%&'Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connector(1 2 3 54 6$) Terminal name1 +V2 Analogue voltage / current output3 0V4 Comparative output 15 Comparative output 26 External input5 I/O CIRCUIT DIAGRAMSWhen using the analogue voltage output, take care to the input impedance of the&&*Furthermore, note that if the cable is extended, the cable resistance will cause the*&NPN output type(Gray) Analoguevoltage / currentoutput (Note 1, 2, 3)(Brown) +V(Black) Comparative output 1(White) Comparative output 2(Pink) External input(Blue) 0V12 to 24V DC±10%+-%& %&(*1)Main circuitPNP output type(Brown) +V(Pink) External input(Black) Comparative output 1(White) Comparative output 2(Gray) Analoguevoltage / currentoutput (Note 1, 2, 3)(Blue) 0V%&%&(*2)Main circuit12 to 24V DC±10%+-*1 *2Non-voltage contact, NPN open-collector transistor orDC 2-wire outputorHigh (5 to 30V DC or Open): Invalid%;<=>?$@J>&Non-voltage contact, PNP open-collector transistor orDC 2-wire outputorHigh (5V to +V DC): Valid%;<K>?$ @J *&)JL@Q&&UX U@!(X>Z* \@Q*#Z&#&&* ]Z#[&&*&6 OUTPUT MODE AND OUTPUT OPERATION The EASY mode, hysteresis mode or window comparator mode can be selected asZ&#Z*L&Z*URefer to in “ 8 MENU SET-TING MODE_#&EASY mode ) ]]#Z*&Z&`J` [&;)L@When the pressure sensor head iscompound pressure type or posi-tive pressure type, hysteresis is&When the pressure sensor head isvacuum pressure type, hysteresis*Z&PressureP0ONOFFComparativeoutputH (Hysteresis)Notes: 1) ` [&jq# in “ 9 PRO MODE_#2) “ ” is displayed for comparative output 1 and “ _#Z*U & INSTRUCTION MANUALHead Separated Digital Pressure Sensor ControllerDPC-100 Series"z ?{$L<<)<<=< |L>!( * Z#{&q& "# & #&ZZ#&}& (Z*#~(#WARNING )*&&*# In case of using devices for personnel protection, use products which meet laws&&& `) z$#- &&&##Z"Z?&&&#*1 PART DESCRIPTIONConnector area for a power supply /I-O cableConnector area for a pressuresensor headOutput 1 operationindicator% Z-parative output 1 is ONOutput 2 operationindicator% Z-parative output 2 is ONMode selection keyUnit display(Note 1, 2)Main displaySub displaySetting valueDOWN keySetting value UP key)JL@& U@!&#& "{_({_2 MOUNTING The sensor mounting bracket MS-DP1-6*QZZ(~&<X)ZM3 (length 6mm) screwswith washers(Accessory with MS-DP1-6)Sensor mounting bracketMS-DP1-6 (Optional) The panel mounting bracket MS-DP1-2 (optional), as well as the front cover MS-DP1-3;@* For mounting of the panel mounting bracket, refer to the Instruction Manual en-closed with MS-DP1-23 CONNECTION OF PRESSURE SENSOR HEAD !&Z && Q&&*Z &!#Z&*Connection method Insert the pressure sensor head cable intothe product’s connector area for the pressure&Disconnection method Pressing the release lever of the pressure&Pressure sensorhead cableRelease leverConnector area of the pressuresensor head cablee-con: 1473562-4! z"{
}'Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connector(1 2 3 4$) Terminal name1 Sensor head supply voltage2 Analogue input3 0V4 Model discrimination signal