Panasonic Diga DMR-EX769 Operating Instructions Manual

Contents

50RQT9308Changing the unit’s settingsSignal ConditionYou can check the quality and strength of digital broadcast signals.Realign the aerial if you are receiving a poor signal.When “Signal Condition” is displayed in grey and cannot beselected:1 Press [EXIT] to exit the screen.2 Press [W X CH] to select a digital channel. “D” appears on theunit’s display.3 Display the Setup menu again (> 49).Press [3, 4] to select “SignalCondition” and press [OK].The quality and strength of thesignal are shown.Press [W X CH] to select thechannel.Signal QualityBelow 2 (display red):The signal quality is so poor that there may be interference in thepictures and sound.2–5 (display orange):The signal quality is basically adequate, but brief interference in thepictures and sound is possible in isolated case.Over 5 (display green):Optimum picture and sound quality.Signal StrengthThe display for signal strength is grey. “0” means signal strength 0%,“10” means signal strength 100%.If the signal is too strong, the display will change from grey to red.Reduce the signal amplification at your aerial.≥When the signal is weak:– adjust the position and direction of the aerial.– adjust the aerial reception with “DVB Manual Tuning” in theSetup menu (> 49).– check that the current digital broadcast channel is correctlybroadcasting.DVB Preferred LanguagePress [3, 4] to select “DVB Preferred Language” and press [OK].§ The language specified as “Original” by the broadcast channel.∫ Settings for Analogue ChannelsPress [OK] to show the following setting.Manual TuningYou can delete analogue channels and set the analogue channeldetails.Press [OK] to show Manual Tuning screen.To delete a programme positionPress [3, 4, 2, 1] to select a programme position and press the“Red” button.To change the tuning settings for individual programmeposition1 Press [3, 4, 2, 1] to select a programme position and press[OK].2 Press [3, 4] to select an item and press [1].You can make the following two settings by selecting the externalinput channel (AV1, AV2, AV3) in step 1.≥Video System (Auto/PAL/SECAM)In order to record properly, make the appropriate settings to matchthe connected equipment.≥Title Page (Auto/Off)You can select up to 2 different subtitles and audio tracks to beused when audio and subtitles digital broadcasts are received.Select the order of priority.If the selected language is not available, then the languageincluded in the broadcast programme is selected.Multi-AudioMulti-Audio ( alternative )[English] [German] [Italian] [French][Spanish] [Catalan] [Basque] [Galician][Corsican] [Original]§SubtitleSubtitle ( alternative )[English] [German] [Italian] [French][Spanish] [Catalan] [Basque] [Galician][Corsican] [Original]§Signal Quality 0 10Signal Strength 0 10DVB ChannelDVB Signal ConditionRETURNChannel +Channel –[CH14] 5 BR3Manual TuningPos Channel CH Pos Channel CHDelete1 ARD 42 ZDF 23 N3 54 HR3 85 BR3 1067891011121314151617181920OK RETURNSELECTPos Programme position in the table(You cannot change the programme position.)Channel To enter or change the Channel of a TVstationPress [3, 4, 2, 1] to enter station nameand press [OK].If the station name needs a blank space,select the blank between “Z” and “¢”.CH To enter newly available TV stations orchange the CH number of an already tunedTV stationPress [3, 4] or the numbered buttons toenter the CH number of the desired TVstation.Wait a few moments until the desired TVstation has been tuned.After the desired TV station is tuned, press[OK].Fine Tuning To obtain the best tuning conditionPress [3, 4] to adjust the best tuningcondition and press [OK].≥Press [1] to return to “Auto”.Video System To select the video system typePress [3, 4] to select “PAL” or “SECAM” ifthe picture lacks colour, and press [OK].≥AutoThis unit automatically distinguishes PALand SECAM signals.≥PALFor receiving PAL signals.≥SECAMFor receiving SECAM signals.Audio Mode To select the audio reception typeIf sound quality is poor, press [3, 4] to select“BG” or “L” and press [OK].≥BGPAL B,G,H/SECAM B,G≥LSECAM L, L’Mono To select the type of sound to be recordedPress [3, 4] to select “On” if the stereosound is distorted due to inferior receptionconditions, or if you want to record the normal(mono) sound during a stereo, bilingual orNICAM broadcast, and press [OK].Title Page To enter the Teletext title page for achannelEntering title page number allows the unit toautomatically record programme and stationnames.Press [3, 4] or numbered buttons to enterthe number and press [OK].PosChannelCHFine TuningVideo System9014AutoManualTuning ARDAutoAudio Mode BGMono OffTitle Page 301RETURNSELECT