Panasonic ER-Q Instruction Manual

3 INPUT AND OUTPUT CIRCUIT DIAGRAM4 MOUNTING● Be sure to turn off the power before carrying out angle adjustment for thisproduct, otherwise accidents or problems with operation may occur.٨ If installing this product directly to the enclosure, use M3 screws. (M3 screwsshould be arranged separately.)٨ If using the ER-QMS1 (optional mounting bracket), use the screws provided withthe mounting bracket.٨ If using SUNX mounting bracket or screws other than the ER-QMS1, do not usescrews which are longer than 10 mm, otherwise they may cause damage tointernal parts when fastened.٨ Tightening torques are 0.5 N・m for M3 screws and 1.2 N・m or less for M4 screws.٨ If using several of these products alongside each other, leave a space of 50 mmor more between each product, otherwise product performance may be adverselyaffected.[If installing this product directly to the enclosure][If using the ER-QMS1 (optional mounting bracket)]5 OPTIONS6 CARE AND MAINTENANCE● Be sure to turn off the power before carrying out cleaning and maintenance.● The discharge needle has a sharp point, so be very careful when cleaning theneedle.● After long periods of use, dirt may adhere to the discharge needles, the areaaround them and the filter. If these areas are not cleaned, charge removalperformance will drop and accidents or problems with operation may occur.Therefore they should be periodically cleaned (discharge needles: about once��INSTRUCTION MANUALStatic Remover Ultra-compact Fan IonizerER-Q CMJE-ERQ No.0031-24VThank you very much for using Panasonic products. Please read thisInstruction Manual carefully and thoroughly for the correct and optimum useof this product. Kindly keep this manual in a convenient place for quickreference.WARNING٨ Never use this product with a device for personnel protection.In case of using devices for personnel protection, use products which meet lawsor standards, such as OSHA, ANSI or IEC etc., for personnel protection applicablein each region or country.٨ ��combustible items being present.٨ ��about once a month), otherwise optimum charge removal performance may not be��٨ If this product is used in an airtight room, ozone emitted from this product may bedetrimental. Therefore, in order for this product to be used in an airtight room, besure to keep the room ventilated.٨ Do not direct ionized air toward the face. Ozone may cause irritation to placessuch as the nose and throat.٨ ��discharge needle, or injuries may result.٨ Be sure to ground the frame ground (F.G.) terminal, otherwise electric chargeremoval may not be reliable.٨ Take care not to let any foreign objects get into the fan air inlet, otherwiseaccidents or operating problems may occur.1 OUTLINE٨ This is a static charge remover which utilizes ion generation by means of coronadischarge.٨ It has a compact shape, so that it can be positioned either vertically or horizontally.٨ It is equipped with an automatic stop function which operates when the dischargeneedle unit has been removed.2 PART DESCRIPTIONIon air outletDischarge needle unit586552603.529333.5Filter coverAlarm indicator(red)2-�3.5 mmmounting holeDischarge indicator(green)Power switchFan speed control(Note 1)�3.7 mm cableConnector 5559-08Pmanufactured by MOLEX2-M3 screws (depth 10 mm) (Note 2)25.419.85.5Notes: 1) Fan speed controlThis is set to MAX fan speed at the time of shipment from the factory.Use a precision screwdriver (-) to adjust the fan speed.2) Screw threads exclusive for SUNX mounting brackets. Do not use them in mounting withother products.��mounting holes.٨ Description of indicatorsDischarge indicator (DSC) ... Lights during discharge(when ions are being generated)Alarm indicator (ALARM) ... Lights when discharge error or discharge checkingoccurs, blinks when fan error occurs.M3 screwSpring washerFlat washer● The dnot rethat yyou re[CleaninԘ Followԙ Use aand thIf thewith aA comthe disԚ Insertthe dis[Discha* Do notneedle* Do notdischar��7 OPNormDischargeDischargFan e* Once ais turne* Elimina* If the ca8 TR● Be suProDischarDischAlarmDischarDischAlarmFanDischAlarm* Indicator* The M3 and M4 screws are included with the ER-QMS1.Ԙ Install bracket 1 to the main unit with the M3 screws.ԙ Install bracket 2 to the main unit with the M4 sems screws, and then use the M4 screwmounting holes to install to the enclosure.Ԙԙ2-M3 screw(depth 10 mm)M3 sems screwBracket 1M4 screwmounting holeM4 sems screwBracket 2g AC adapterModel No. Details Model No. DetailsModel No. DetailsModel No. DetailsModel No. Detailsg Replacement discharge needle unitUnit with tungsten needlesg Replacement air filter5-piece air filter setg Cable with connectorsCable length 2 mCable length 5 mg Mounting bracketMounting bracket for airdirection adjustmentIN: 100 to 240 V AC, 50/60 Hz, 40 VAOUT: 24 V DC, 750 mAER-VAPS1ER-QANTER-QFX5ER-QCC2ER-QCC5ER-QMS1124 V DC±10 Ċ30 VDC MAXD 1Tr1ZD1D 2LoadCOM (+)50 mA MAX(Black) Error outputTr2ZD 2D 3LoadCOM(-)50 mA MAX(Orange) Check output(Green) F.G.(Brown) +24 V(Blue) 0 VInternal circuits User’s circuitsMain circuitD 1 : Power supply reverse connectionprotection diodeD2 , D3 : Output protection diodesZD 1 , ZD2 : Surge voltage absorption Zener diodesTr1 , Tr2 : NPN output transistorsConnector pin layout diagramTerminal no. Terminal name Lead wire color0 VCOM (-)N.C. (Not used)F.G.24 VCOM(+)Check outputError outputBlueGreenBrownOrangeBlackFront viewԘTurn theԙ RemoveԚRemovefilter isusing itԛ Install th* If the filte* If the filte* Be carefufilter.Ramco National800-280-6933 | nsales@ramcoi.comwww.panasonicsensors.com

/ 2

Related manuals for Panasonic ER-Q