Panasonic FM-252-4(-P) Instruction Manual

Never use this product in a device for personnel protection. In case of using devices for personnel protection, use products which meetlaws and standards, such as OSHA, ANSI or IEC etc., for personnel protec-tion applicable in each region or country.PART DESCRIPTION1 one-side reverse direction, a direction opposite to the forward direction display will be the Flow direction set-ting PRO MODE.”2) ø4 push-in joint / ø8 push-in joint is incorporated into FM-!-4 (-P) / FM-!-8 (-P), respec-tively. The push-in joint is not incorporated into the aluminum body type.MODE keyForward direction display(Note 1)UP keyDOWN keyConnector areafor piping(Note 2)Connector areafor piping(Note 2)Comparative output 2 indicator (Green)Comparative output 1 indicator (Green)Main display(Green / Red)Sub display (Green / Red)Connector area forcable with connectorPIPING2 " ## $ % & &# & $& ' *$product. Before using the product,make sure to check that & %+#* Material of tube Tube diameter Allowable diameterPolyamid ø4, ø8 Within ±0.1mmPolyurethane ø4 Within ±0.1mmø8 Within +0.1 / -0.15mm 6## %# * # + %# 7+ # $ +*side (upstream) of the product since the compressed air from the compressorcontains drain (water, oil oxide and foreign materials, etc.). Mesh (wire net) in the$& & * $ $ 9#* ## %# $ +* $& + %# +: + # PneumaticspressuresourceFilter Regulator Flow sensor(This product)Air dryer Oil mist filter(Micro-alescer) & :#: $ +* $& #* & #$ $ %-tion valve. The product may malfunction or break if subject to splattering grease or oil, etc. & $& $ : % #* ## %# %# $$* ;<+ # & $:& + # &+ +$ dew point and ambient temperature of the product, use the product under theconditions that dew condensations will not be formed in the inside of pipe. In case of mounting commercial joint to the aluminum body type, apply a spanner onthe metal part of this product and tighten by the tightening torque of 16 to 18N·m.If excessive torque is applied, the commercial joint or the main body may break. When piping, care must be taken that foreign materials such as sealing tapeand adhesive must not enter into the inside. If the foreign materials are en-tered, the product may malfunction or break. Make sure to mount the joint when using the product with its secondary side (downstream) $ 6 ' +& $ %# $& +* ## MOUNTING4Horizontal mounting Use M3 screw and the tightening torque should be 0.5N·m.Vertical mounting Use M3 screw and the tightening torque should be 0.5N·m. When using sensor mounting bracket When mounting the product on the sensor mounting bracket MS-FM2-1 (op-tional) or MS-FM2-2 (optional), use the M3 screw (length 6mm) attached tothe sensor mounting bracket. The tightening torque should be 0.5N·m.Use M3 screw to mount the sensor mounting bracket on a sensing surface. Use MS-FM2-1 Use MS-FM2-22717mm2-ø3.4through-hole(Unit: mm)DimensionM3 screw(Please arrange separately.)15.59.52-M3depth 5M3 screw(Please arrange separately.)(Unit: mm)Dimension30132-M3 depth 5M3 screw(Please arrange separately.)(Unit: mm)Dimension3063.5(Unit: mm)DimensionM3 screw(Please arrange separately.)M3 screw (length 6mm)(Attached to MS-FM2-1)304063.5(Unit: mm)DimensionM3 screw(Please arrange separately.)M3 screw (length 6mm)(Attached to MS-FM2-2)I/O CIRCUIT DIAGRAMS5 NPN output type PNP output typeInternal circuit Users’ circuit(Brown) +VLoadLoad(White) CH2 (Comparative output 2 / External input)(Blue) 0V(Note)(Note 2)9$$K QX(*1)(*2)(Black) CH1(Comparative output 1)50mA max.50mA max.(Gray) Analogue voltage output+-12 to 24V DC±10%Terminal No. Color code of cable with connectorMain circuitInternal circuit Users’ circuitColor code of cable with connector(Brown) +VLoadLoad(White) CH2 (Comparative output 2 /External input)(Blue) 0V(Note)(*1)(*3)(Black) CH1(Comparative output 1) 50mAmax.50mA max.(Gray) Analogue voltage output+-12 to 24V DC±10%Terminal No.Main circuit(Note 2)9$$K QX*2: When using CH2 as an external inputNon-voltage contact, NPN transistor orDC 2-wire outputorHigh (+5 to +V or Open): InvalidLow (0 to +0.4V): Valid*3: When using CH2 as an external inputNon-voltage contact, PNP transistor orDC 2-wire outputorHigh (+5 to +V): ValidLow (0 to +0.6V or Open): Invalid*1: When using CH2 as a comparative output 2Notes: 1) As for the aluminum body type, variable resistor (clamping voltage: approx. 40V) is con-nected between the internal power circuit and the metal body to prevent breakdown of the [ +# * \] $ &$$#* + & 7^ : that is connected to 0V. High potential and insulation resistance tests between the internalpower circuit and the metal body must not be done.2) Short-circuit protection is not incorporated into the analogue voltage output.Do not connect the power supply or capacitive load directly to the analogue voltage output. (Sensor body)TerminalNo.Color code of thecable with connector Terminal name1 Brown +V2 Black CH1 (comparative output 1)3 White CH2 (comparative output 2 / external input)4 ^* Analogue voltage output5 Blue 0V1 2 3 4 5WIRING3ConnectorcoverConnection method Insert the cable with connector CN-F15-C1 (accessory) into theconnector area of this product and mount the connector cover.Disconnection method Remove the connector cover and pressing the release lever of the cable withconnector, pull out the connector.Note: Do not pull by holding the cable without pressing the release lever, as this can cause cablebreak or connector break.OUTPUT MODE6 " &$& _ + +$ + * + -grated output mode or integrated pulse output mode can be selected as theoutput mode for comparative output 1 and comparative output 2.` Output mode and threshold value setting mode MENUSETTING MODE” for details.INSTRUCTION MANUAL6 6 "*$ ^ # zFM-200 Series{|{};; ;;~}]Thank you very much for purchasing Panasonic products.Please read this Instruction Manual carefully and thoroughly for the correct andoptimum use of this product.Kindly keep this manual in a convenient place for quick reference.D2-255025-ARamco National800-280-6933 | nsales@ramcoi.comwww.panasonicsensors.com

/ 4

Related manuals for Panasonic FM-213-4(-P)