INSTRUCTION MANUAL FX-501MJE-FX501C No.0035-73VThank you very much for purchasing Panasonic products.Please read this Instruction Manual carefully and thoroughly for the correct andoptimum use of this product.Kindly keep this manual in a convenient place for quick reference.WARNING Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products whichmeet laws and standards, such as OSHA, ANSI or IEC etc., for personnelprotection applicable in each region or country.1 INTENDED PRODUCTS FOR CE MARKING This product complies with the following standards / regulations.EMC Directive 2004/108/ECANSI/UL 60947-5-2, CAN/CSA C22.2 No.14S1-G-1-2009, S2-W-5-2009 Caution about UL recognitionIn case requiring conformity of UL listing mark or C-UL listing mark, USe class2 power supply unit. Contact for CEPanasonic Electric Works Europe AGRudolf-Diesel-Ring 2, D-83607 Holzkirchen, GermanyPanasonic Marketing Europe GmbH Panasonic Testing CenterWinsbergring 15, 22525 Hamburg,Germany2 PART DESCRIPTIONMODE indicator: PRO (Yellow)MODE indicator: L / D (Yellow)Digital display(Green / Red)UP keyTeachingThreshold value Select setting itemsSET keyTeachingC o n f i r m s e t t i n gcontentsDOWN keyTeaching Select setting itemsSensing outputoperation indicator(Orange)MODE keySelect ModesCancel during settingMODE indicator: CUST (Yellow)Pressing down SET key + MODE key for 3 sec : Set key lock or release key lock3 MOUNTINGHow to connect1. Fit the rear part of the mounting sec- ! "2. Press down the rear part of themounting section of the unit on theDIN rail and fit the front part of themounting section to the DIN rail.How to remove1. Push the controller forward.2. # to remove it.2. Lift up1. Push forward2. Press down1. Fit35mm width DIN rail $ % " & % % ' "1. Snap the fiber lock lever down till itstops completely.2. % '* inlets until they stops. (Note)3. Return the fiber lock lever to theoriginal position till it stops.Fiber lock leverFiber forreceiver1. Snap3. Return2. InsertFiber for emitter! ; = %? @ % * &% &FD-G4 or FD-FM2& % % B QZ[ B% % B % "If they are inserted in reverse, the sensing performance will deteriorate.4 INSTALL MORE AMPLIFIER OF SERIES CONNECTION TYPE Make sure that the power supply is OFF while adding or removing the seriesconnection type. In case 2 or more the series connection types are connected in cascade,make sure to mount them on a DIN rail. % % %* & ?\\ % %* % % using a main connection cable. When connecting 2 or more the series connection types in cascade, use thesub cable (optional) for the second series connection type onwards. & Q MOUNTING.”How to cascade1. ] & * &on the DIN rail.2. ? % other, and connect the quick-connection cables.3. Mount the end plates MS-DIN-E(optional) at both the ends to holdthe amplifiers between their flatsides.4. % '? plates.How to Remove1. Loosen the screws of the endplates.2. Remove the end plates.3. Slide the amplifiers and removethem one by one. SlideCommunicationwindowSlideMain cable(Optional)Sub cable(Optional)End plateMS-DIN-E (Optional)End plateMS-DIN-E(Optional)5 I/O CIRCUIT DIAGRAMS+-12 to 24V DC%Main circuit (Brown) +V (Note)(Black) Sensing output(Blue) 0V (Note)LoadMain circuit (Brown) +V (Note)(Black) Sensing output(Blue) 0V (Note) Load+-12 to 24V DC%Note: The quick-connection sub cable does not incorporate +V (brown) and 0V (blue). The power is supplied fromthe connector of the main cable.231 Terminal No. Terminal name1 +V2 Sensing output3 0V6 OPERATION PROCEDUREThe changed settings are not stored if turning the power OFF while " &% * `j * turning the power OFF. When turning ON the power, RUN mode is displayed and the digital displayshows the threshold value (green) and the incident light intensity (red).Displays threshold value (green) and incident light intensity (red). % & j *%j %can be set.For setting method of each function, refer to “ TEACHINGMODE,” “ THRESHOLD VALUE FINE ADJUSTMENT FUNC-TION,” or “ KEY LOCK FUNCTION.”Select either Light-ON or Dark-ON. For the setting, refer to “ SENSING OUTPUT OPERATIONMODE.”The default setting is “ ” (Light-ON).An item set in CUSTOM mode (Response time setting, Emissionpower setting and Hysteresis setting) is displayed.For details, refer to “ CUSTOM MODE.”The default setting is “ ” (response time setting).Advanced setting can be done.For the setting, refer to “ PRO MODE.”5DPFR1DWLRQDO *RW4XHVWLRQV" QVDOHV#UDPFRLFRP ZZZ3DQDVRQLF6HQVRUVFRPFor application support or selecting the best fiber cable Contact Ramco Innovations
|
