Panasonic HDC-TM700P Service Manual

Also see for HDC-SD700EB: Service manual

Contents

Panasonic HDC-TM700P Service Manual Manual pdf 15 page image

S-1S1. About Indication of The Schematic Diagram ............................ S-1S1.1. Important Safety Notice......................................................... S-1S2. Voltage Chart ........................................................................... S-2S2.1. Main P.C.B. ........................................................................... S-2S3. Block Diagram .......................................................................... S-3S3.1. System Control Block Diagram ............................................. S-3S3.2. Video/Audio Signal Process Block Diagram ......................... S-4S3.2.1. Video/Audio Signal Process Block Diagram (1) ................. S-4S3.2.2. Video/Audio Signal Process Block Diagram (2) ................. S-5S3.3. Camera Block Diagram ......................................................... S-6S3.4. Lens Drive Block Diagram..................................................... S-7S3.5. Power Supply Block Diagram................................................ S-8S4. Schematic Diagram ................................................................ S-10S4.1. Main CN Schematic Diagram .............................................. S-10S4.2. Process Schematic Diagram ............................................... S-14S4.3. Lens Drive Schematic Diagram........................................... S-18S4.4. Syscon Schematic Diagram ................................................ S-22S4.5. RTC Schematic Diagram .................................................... S-26S4.6. Video Schematic Diagram................................................... S-28S4.7. AVIO Schematic Diagram.................................................... S-32S4.8. HDMI Schematic Diagram................................................... S-33S4.9. Power Schematic Diagram.................................................. S-34S5. Print Circuit Board .................................................................. S-38S5.1. Main P.C.B. ......................................................................... S-38S5.1.1. Main P.C.B. ...................................................................... S-38S5.1.2. Main P.C.B. Address Information ..................................... S-39S6. Replacement Parts List .......................................................... S-41Table of contentsService ManualVM1002004CEDiagrams and ReplacementParts ListVol. 2(K)...........Black TypeColour[HDC-SD707](S)...........Silver Type(K)...........Black TypeModel No.HDC-TM700PHDC-TM700PCHDC-TM700PUHDC-TM700EBHDC-TM700ECHDC-TM700EEHDC-TM700EFHDC-TM700EGHDC-TM700EPHDC-TM700GCHDC-TM700GDHDC-TM700GKHDC-TM700GTHDC-SD700EBHDC-SD700ECHDC-SD700EEHDC-SD700EFHDC-SD700EGHDC-SD700EPHDC-SD700GCHDC-SD700GNHDC-SD707EGHigh Definition Video Camera[HDC-TM700/SD700]Name of SignalOFTR FEP This signal is connectedto the FEP schematic diagram.Circuit name being connected.6.Use the parts number indicated on the Replacement Parts List .7.Indication on Schematic diagrams:5.The voltage being indicated here may be include observational-error (deviation) due tointernal-resistance and/or reactance of equipment. Therefore, handle the valueindicated on here as reference.4.Although the voltage and waveform available on here is measured with standard frame,it may be differ from actual measurement due to modification of circuit and so on.3.The voltage being indicated on the schematic diagram is measured in"Standard-Playback" mode when there is no specify mode is mentioned.2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.when the TP (Test Point) indicated as " " mark.1.Although reference number of the parts is indicated on the P.C.B. drawing and/orschematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICSS1. About Indication of The Schematic DiagramS1.1. Important Safety Notice