INSTRUCTION MANUALContact-Type Digital Displacement Sensor / Sensor Head+*6ƑMJE-HGS1010 No.0074-49VThank you very much for purchasing Panasonic products. Read this Instruction Man-ual carefully and thoroughly for the correct and optimum use of this product. Kindlykeep this manual in a convenient place for quick reference.WARNINGƔ Never use this product as a device for personnel protection.Ɣ When using devices for personnel protection, use products that meet the lawsand standards for personnel protection that apply in each region or country, suchas OSHA, ANSI and IEC.This document provides a brief summary of mounting and other related information.For detailed information, refer “our web site (https://panasonic.net/id/pidsx/global) ” .1 STANDARDS AND REGULATIONSƔ This product conforms to the standards and regulations below.EMC Directive2 CONTENTS OF PACKAGESensor head 1 pc.Mounting nut 1 pc.Sensor head fastening wrench 1 pc.Rubber bellows (+*6Ƒ5 only) 1 pc.Instruction Manual (English / Japanese, Chinese / Korean) 2 pcs.General Information for Safety, Compliance, and Instructions(23 languages) 1 pc.3 DESCRIPTION OF PARTSSensor head connection cable connectorOperation indicator (Orange / Green)Mounting nutRubber bellowsProbe4 MOUNTINGƔ When tightening the mounting nut, take care not to damage the rubber bellows.Ɣ If the rubber bellows is deformed, a load will occur when the spindle operatesand damage may result.Ɣ 1RWHWKDWWKHPRXQWLQJGLUHFWLRQRIWKHSURYLGHGPRXQWLQJQXWGLႇHUVDFFRUGLQJto the thickness of the housing.1. Open a hole in the housing in which the sen-sor head will be mounted.Mounting hole Housing thicknessHG-S1010 R ࠊHG-S1110 R ø8H7 㸩0.0150 mm 6.5㹼12.5mmHG-S1032 ø12H7 㸩0.0180 mm 6.5㹼10.5mmHG-S1050 6.5㹼12.5mm2. Insert the sensor head into the hole youopened in the housing, and fasten lightlywith the provided mounting nut.Housing thicknessMounting holeMounting nut(Accessory)Installation of mounting nut attachmentHousing thicknessA BHG-S1010 R ࠊHG-S1110 R 6.5㹼10mm 10㹼12.5mmHG-S1032 6.5㹼8.5mm 8.5㹼10.5mmHG-S1050 8.5㹼12.5mm3. Fasten the sensor head.When fastening the sensor head, tighten themounting nut with a wrench while holding thesensor head in place with the sensor headfastening wrench as shown at right.Tighten to a torque of 12.5N·m or less(HG-S1032 / HG-S1050: 15N·m or less).4. Make sure that the rubber bellows has notbecome deformed as shown at right.If the rubber bellows is deformed, restore thenormal shape by rotating the bellows or oth-erwise.Connecting the sensor head connection cableƔ When attaching the connector, make sure it is firmly tightened. If loose, theFRQQHFWRUPD\FRPHRႇDQGFDXVHDQHUURUƔ When disconnecting, always make sure that the fastening ring has been com-pletely loosened before pulling out the cable.Risk of damage if you pull the cable with excessive force (15N or more) with thefastening ring tightened.How to connect1. Insert the sensor head connectioncable into the connector for thesensor head connection cable onthe sensor head.2. Turn the fastening ring on the sen-sor head connector in the directionVKRZQWR¿UPO\WLJKWHQWKHULQJHow to remove1. Turn the fastening ring on the sen-sor head connector in the directionshown to loosen the ring.2. Grasp the connector and pull up toremove the cable. 2. Pull out1. Loosen5 SPECIFICATIONSType10mm typeGeneral purpose High precisionStandard type Low measuringforce type Standard type Low measuringforce typeModel No. HG-S1010 HG-S1010R HG-S1110 HG-S1110RPosition detection method Optical absolute linear encoder methodMeasurement range 10mmStroke 10.5mm or moreMeasur-ing force(Note 1)(Note 2)Downwardmount1.65N or less1.10N (Note 3)0.35N or less0.30N (Note 3)1.65N or less1.10N (Note 3)0.35N or less0.30N (Note 3)Upward mount 1.35N or less0.85N (Note 3) - 1.35N or less0.85N (Note 3) -Side mount 1.50N or less0.95N (Note 3)0.25N or less0.20N (Note 3)1.50N or less0.95N (Note 3)0.25N or less0.20N (Note 3)Resolution 0.5μm 0.1μmSampling cycle 1msIndicationaccuracy(P-P)Full range 2.0μm or less 1.0μm or lessLimited range 1.0μm or less (any 60μm) 0.5μm or less (any 60μm)Hot swap function IncorporatedProtective structure IP67 (IEC) (Note 4) - IP67 (IEC) (Note 4) -Ambient temperature -10 to +55°C (No dew condensation or icing allowed), Storage: -20 to +60°CAmbient humidity 35 to 85% RH, Storage: 35 to 85% RHMechanical life (Note5) 100 million times or more (reference value)Tip deviation amount 35μm (typical value)Grounding method Capacitor groundingMaterial Body: Zinc, Holder: Stainless steel, Spindle: Tool steel, Probe: Ceramic, Rubberbellows: NBR (black)Weight (main unit only) Approx. 80g1RWHV 0HDVXUHGDWDQDPELHQWWHPSHUDWXUHRI&XQOHVVRWKHUZLVHVSHFL¿HG2) +*6Ƒ5 is standard state without the rubber bellows.3) Typical value near center of measurement.4) Excludes damage and deterioration to the rubber bellows due to external causes.5) Typical value in a clean environment in which there is no contact with liquids such as water or oil, and no set-tling of particulate matter.Mounting nut with thethread facing upBHousingThreadMounting nut with thethread facing downAHousingThreadSensor headfastening wrench(Accessory)Wrench1. Insert2. Tightenfastening ring
