INSTRUCTION MANUALContact-Type Digital Displacement Sensor / Sensor Head Air-Driven Type+*6Ƒ$&MJE-HGSAC No.0074-51VThank you very much for purchasing Panasonic products. Read this Instruction Man-ual carefully and thoroughly for the correct and optimum use of this product. Kindlykeep this manual in a convenient place for quick reference.W A R N I N GƔ Never use this product as a device for personnel protection.Ɣ When using devices for personnel protection, use products that meet the lawsand standards for personnel protection that apply in each region or country, suchas OSHA, ANSI and IEC.This document provides a brief summary of mounting and other related information.For detailed information, refer “our web site (https://panasonic.net/id/pidsx/global) ”1 STANDARDS AND REGULATIONSƔ This product conforms to the standards and regulations below.EMC Directive2 CONTENTS OF PACKAGESensor head 1 pc.Mounting nut 1 pc.Sensor head fastening wrench 1 pc.Air tube clamp 1 pc.Instruction Manual (English / Japanese, Chinese / Korean) 1 pc. eachGeneral Information for Safety, Compliance, and Instructions(23 languages) 1 pc.3 DESCRIPTION OF PARTSWhen air is suppliedSpindleSeal cap (Note)Operation indicator(Orange / Green)Mounting nutAir tube jointProbeSensor head connectioncable connectorNote: The seal cap is provided as a maintenance part. HG-SASCX5 (5 pcs. per set)4 MOUNTINGMounting on the housingƔ 1RWHWKDWWKHPRXQWLQJGLUHFWLRQRIWKHSURYLGHGPRXQWLQJQXWGLႇHUVDFFRUGLQJto the thickness of the housing.1. Open a hole in the housing in which thesensor head will be mountedThickness ofthe housing Mounting holeȭ8H7 +0.0150 mm2. Insert the sensor head into the hole you opened in thehousing, and fasten lightly with the provided mounting nut.Thickness of the housingA BHG-S1010-AC, HG-S1110-AC 6.5 to 10mm 10 to 12.5mmAHousingBHousingThreadThreadMounting nut with thethread facing downMounting nut with thethread facing upNote: Please use within a the thickness of the housing range of 6.5~12.5mm.Mounting nut(Accessory)3. Fasten the sensor head.Tighten the mounting nut with a wrenchwhile holding the sensor head in placewith the sensor head fastening wrench asshown.Tighten to a torque of 12.5N·m orless.Mounting nut(Accessory)Sensor headfastening wrench(Accessory)Connecting the sensor head connection cableƔ :KHQDWWDFKLQJWKHFRQQHFWRUPDNHVXUHLWLV¿UPO\WLJKWHQHG,IORRVHWKHFRQ-QHFWRUPD\FRPHRႇDQGFDXVHDQHUURUƔ When disconnecting, always make sure that the fastening ring has been com-pletely loosened before pulling out the cable.Risk of damage if you pull the cablewith excessive force (15N or more) with the fastening ring tightened.Ɣ Sensor head connection cables with an L-shaped connector cannot be used.How to connect1. Insert the sensor head connectioncable into the connector for thesensor head connection cable onthe sensor head.2. Turn the fastening ring on the sen-sor head cable in the directionVKRZQWR¿UPO\WLJKWHQWKHULQJ1. Insert2. Tightenfastening ringHow to remove1. Turn the fastening ring on the sen-sor head cable in the directionshown to loosen the ring.2. Grasp each connector on the sen-sor head connection cable and pullout to remove.2. Pull out1. LoosenConnecting the air tubeƔ :KHQFRQQHFWLQJWKHDLUWXEH¿UPO\VHFXUHLWZLWKWKHDLUWXEHFODPSSURYLGHG,Ithe air tube is used without inserting or securing it properly, there is a danger thatWKHDLUWXEHPD\FRPHRႇZKLOHLWLVEHLQJXVHGHow to connect1. While loosening the air tube clamp, slide it from the tip of the air tube and thenrelease it when it reaches halfway through the tube.2. Insert the tip of the air tube until it reaches the root of the joint on the sensorhead3. Move the air tube clamp and secure the tip of the air tube.4-mm-diameter air tubeAir tube clamp(Accessory)How to disconnect1. While loosening the air tube clamp, move it halfwaythrough the air tube.2. Grasp the sensor head and pull out the air tube.Note: Take care not to lose the air tube clamp.5 AIR CIRCUIT (RECOMMENDED)Ɣ &UHDWHDQDLUFLUFXLWOLNHWKHRQH UHFRPPHQGHG VKRZQLQWKH¿JXUHEHORZDQGif necessary, adjust the speed of the spindle with the speed control valve.Air pressure sourcePrecision regulator3-port solenoid valve Speed control valveFilter + Mist separator + RegulatorNotes: 1) Supply clean air (free from moisture, oil, dust, or other foreign objects) to this product.2) Air pressure may decrease, depending on the length of the air pipe from the air supply source or any pneu-PDWLFFRPSRQHQWV VXFKDVQHHGOHYDOYHVVSHHGFRQWUROOHUVRUPLQL¿OWHUV WKDWDUHDGGHG7DNHFDUHWRHQ-VXUHWKDWDLUSUHVVXUHVXSSO\WRWKHSURGXFWLVVXႈFLHQW6HOHFWSQHXPDWLFFRPSRQHQWVVXLWDEOHIRUWKHVXS-plied air pressure.3) The 3-port solenoid valve and speed control valve have their respective mounting directions. Mount eachvalve in their correct direction by referring to the above diagram.4) $¿OWHUZLWKDUDWHG¿OWUDWLRQRIȣPRUOHVVDQGDPLVWVHSDUDWRUZLWKDUDWHG¿OWUDWLRQRIȣm or less arerecommended.