Panasonic KX-FLB802CX Service Manual

29KX-FLB802CX/KX-FLB812CX/KX-FLB802CXS/KX-FLB812CXSNote 1 - Standard facsimile units conforming to T.2 must have the following capability: Index of cooperation (IOC)=264.Note 2 - Standard facsimile units conforming to T.3 must have the following capability: Index of cooperation (IOC)=264.Note 3 - Standard facsimile units conforming to T.4 must have the following capability: Paper length=297 mm.21, 22, 23(0, 0, 0)(0, 0, 1)(0, 1, 0)(1, 0, 0)(0, 1, 1)(1, 1, 0)(1, 0, 1)(1, 1, 1)Minimum scan line time capability of the receiver20 ms at 3.85 l/mm: T 7.7 = T3.8540 ms at 3.85 l/mm: T 7.7 = T3.8510 ms at 3.85 l/mm: T 7.7 = T3.855 ms at 3.85 l/mm: T 7.7 = T3.8510 ms at 3.85 l/mm: T 7.7 = 1/2 T 3.8520 ms at 3.85 l/mm: T 7.7 = 1/2 T 3.8540 ms at 3.85 l/mm: T 7.7 = 1/2 T 3.850 ms at 3.85 l/mm: T 7.7 = T3.85Minimum scan line time20 ms40 ms10 ms5 ms0 ms24 Extend field Extend field25 2400 bit/s handshaking 2400 bit/s handshaking26 Uncompressed mode Uncompressed mode27 Error correction mode Error correction mode28 Set to “0”. Frame size 0 = 256 octets 1 = 64 octets29 Error limiting mode Error limiting mode30 Reserved for G4 capability on PSTN Reserved for G4 capability on PSTN31 T.6 coding capability T.6 coding enabled32 Extend field Extend field33(0)(1)Validity of bits 17, 18Bits 17, 18 are validBits 17, 18 are invalidRecording widthRecording width indicated by bits 17, 18Recording width indicated by this field bit information34 Recording width capability 1216 picture elements alongscan line length of 151 ± mm 1%Middle 1216 elements of 1728 picture elements35 Recording width capability 864 picture elements along scanline length of 107 ± mm 1%Middle 864 elements of 1728 picture elements36 Recording width capability 1728 picture elements alongscan line length of 151 ± mm 1%Invalid37 Recording width capability 1728 picture elements alongscan line length of 107 ± mm 1%Invalid38 Reserved for future recording width capability.39 Reserved for future recording width capability.40 Extend field Extend field41 R8×15.4 lines/mm R8×15.4 lines/mm42 300×300 pels/25.4 mm 300×300 pels/25.4 mm43 R16×15.4 lines/mm and/or 400×400 pels/25.4 mm R16×15.4 lines/mm and/or 400×400 pels/25.4 mm44 Inch based resolution preferred Resolution type selection“0”: neuritic based resolution“1”: inch based resolution45 Metric based resolution preferred Don’t care46 Minimum scan line time capability for higher resolutions“0”: T15.4 = T7.7 “1”: T15.4 = 1/2T7.7Don’t care47 Selective Polling capability Set to “0”.48 Extend field Extend fieldSignal Identification Signal Format FunctionTraining 1 ——————— A fixed pattern is transmitted to the receiving side at a speed (2400to 14400 bps) designated by DCS, and the receiving side optimizesthe automatic equalizer, etc., according to this signal.Bit No. DIS/DTC DCS