Panasonic KX-T206E Installation Manual

Also see for KX-T206E: User manual User manual User manual Product description

Panasonic KX-T206E Installation Manual Manual pdf 28 page image

28System ProgrammingOther Programs• Host PBX Access Code AssignmentAssigns a Host PBX access code to make anoutside call, if the system is installed behind thehost PBX. A pause is automatically insertedafter the access code and the toll restrictionfeature applies to the number after the code.Input Format: #21 [A] [code] #• [A]=1: CO1/ 2: CO2• [code] = 2 digits max. (Default : Not stored)• Hookswitch Flash Time AssignmentSets the time to send the flash signal to each COline.Input Format: #22 [A] [B]• [A]=1: CO1/ 2: CO2• [B]=0: 80 ms/ 1: 100 ms (default)/ 2: 160 ms/3: 300 ms/ 4: 600 ms / 5: 900 ms /6: 1200 ms• CO Pulse SelectionAssigns to send the pulse to CO line during aconversation with an outside party when the “#01Dial Type Selection” program is assigned as“Pulse”.Input Format: #23 [A]• [A]=0: DISABLE/ 1: ENABLE (default)• Call Incoming Mode SelectionAssigns whether to use the DISA feature or not.This program is available when the DISA/FAXDetect card is installed.Input Format: #24 [A] [B]• [A]=1: CO1/ 2: CO2• [B]=0: NORMAL (default)/ 1: DISA• Bell Off DetectionSets the time between one bell signal detectionand the next signal from a Central Office.Input Format: #25 [A]• [A]=1: 6 SEC/ 2: 3 SEC (default)• Intercom Alerting AssignmentAssigns the intercom alerting mode to eachextension when an intercom call reaches.Input Format: #30 [A] [B]• [A]=1 through 6 (corresponding to extensionno. 21 through 26)• [B]=0: TONE (default)/ 1: VOICE• Paralleled Telephone ConnectionAssigns whether each extension will be con-nected in parallel with a single line telephone ornot.Input Format: #31 [A] [B]• [A]=1 through 6 (corresponding to extensionno. 21 through 26)• [B]=0: DISABLE (default)/ 1: ENABLE• Tone Waiting Time After OGMSets the time between sending an outgoingmessage and sending the ringback tone.Input Format: #40 [A]• [A]=0: 0 SEC/ 1: 5 SEC (default)/ 2: 10 SEC/3: 15 SEC• Hold Recall TimeAssigns the length of the hold recall timer andtransfer recall timer. The hold recall timer isused to alert an extension that a call has beenheld for an extended period of time. Thetransfer recall timer is used to alert an extensionthat a transferred call has not been answered foran extended period of time.Input Format: #50 [A]• [A]=0: 30 SEC (default)/ 1: 1 MIN / 2: 2 MIN/3: 3 MIN/ 4: 4 MIN/ 5: DISABLE• Hold Mode Selection for SLTAssigns the method to put a call on hold withSLTs.Input Format: #51 [A]• [A]=1: MODE 1 (hooking) (default)2: MODE 2 (hooking and dial 6)• CO Line Access Number SelectionSelects the automatic line access number.Input Format: #52 [A]• [A]=1: 9 (default)/ 2: 0• Conference ToneAssigns whether or not to delete the conferencetone. You hear the tone when the conference orthe executive busy override feature begins andfinishes.Input Format: #53 [A]• [A]=0: DISABLE/ 1: ENABLE (default)• Music on Hold UseSelects whether or not to use internal music asthe music on hold.Input Format: #54 [A]• [A]=1: MODE 1 (NO MUSIC) (default)/2: MODE 2 (MUSIC)