INSTRUCTION MANUAL'LJLWDO/DVHU6HQVRU$PSOL¿HU/6Ƒ&ME-LS501C2 No.0090-49VThank you very much for purchasing Panasonic products. Please read this Instruc-tion Manual carefully and thoroughly for the correct and optimum use of this product.Kindly keep this manual in a convenient place for quick reference.WARNINGƔ Never use this product as a sensing device for personnel protection.Ɣ In case of using sensing devices for personnel protection, use products whichmeet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protec-tion applicable in each region or country.1 STANDARDS AND REGULATIONSƔ This product complies with the following standards and regulations.EU Law:EMC Directive 2014/30/EUBritish Legislation:EMC Regulations 2016/1091 ̼Applicable StandardsEN IEC 60947-5-2:2020 PART DESCRIPTIONDigital display (Green / Red)Laser emis-sion indicator(Green)MODE indicator: PRO (Yellow)MODE indicator: L / D (Yellow)UP key• Teaching• Threshold value fineadjustment• Select setting itemsSET key• Teaching• &RQ¿UPVHWWLQJFRQWHQWVDOWN key• Teaching• Threshold value fineadjustment• Select setting itemsMODE key• Select Modes• Cancel during setting• Press down for 2 sec. or more:Switch the sensing output 1 / 2.Sensing output 2 opera-tion indicator (Orange)Sensing output 1 opera-tion indicator (Orange)Sensing output 1 selec-tion indicator (Yellow)Sensing output 2 selec-tion indicator (Yellow)MODE indicator: CUST (Yellow)Pressing down SET key + MODE key for 3 sec : Set key lock or release key lock3 MOUNTINGHow to connect1. Fit the rear part of the mounting section of theDPSOL¿HURQD',1UDLO2. Press down the rear part of the mounting sec-WLRQRIWKHXQLWRQWKH',1UDLODQG¿WWKHIURQWpart of the mounting section to the DIN rail.2. Press down1. Fit35mm width DIN railHow to remove1. Push the controller forward.2. /LIWXSWKHIURQWSDUWRIWKHDPSOL¿HUWRUHPRYHit.2. Lift up1. Push forward4 CONNECTION OF A SENSOR HEADMake sure that the power supply is OFF while connecting or disconnecting the sen-sor head LS-H series (optional).How to connect1. Insert the connector of the sensor headLS-H series (optional) into the connectorarea for the sensor head of this productDVVKRZQLQWKHULJKW¿JXUH2. Fit the connector cover.2. Fit1. InsertConnectorcoverSensor head side connectorConnector area for thesensor headHow to remove1. Pressing the release lever attached tothe connector of the sensor head, pullout the connector.1. Pull outRelease leverNote: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connectorbreak.Terminal No. Color code1 Purple2 White3 Shield4 Shield5 Black6 Pink3456125 I/O CIRCUIT DIAGRAMS /6&!Load+-12 to 24V DC+10-15 %LoadLoad WRMain circuit(Brown) +V(Pink) External input(Black) Sensing output 1(White) Sensing output 2(Blue) 0V(Gray) Monitor current output (4 to 20mA) /63&!Load+-12 to 24V DC+10-15 %LoadLoad WR(Brown) +V(Pink) External input(Black) Sensing output 1(White) Sensing output 2Main circuit(Blue) 0V(Gray) Monitor current output (4 to 20mA)Note: Make sure to insulate the ends of the unused lead wires.6 OPERATION PROCEDUREƔ The sensing output can be switched to sensing output 1 or sensing output 2 byholding down the mode key.Ɣ The changed settings are not stored if turning the power OFF while setting.7KHUHIRUHFRQ¿UPWKHVHWWLQJVE\SUHVVLQJWKH6(7NH\EHIRUHWXUQLQJWKHSRZHUOFF.Ɣ When turning ON the power, RUN mode is displayed and the digital display showsthe threshold value (green) and the incident light intensity (red).• Displays threshold value (green) and incident light intensity (red).• 7HDFKLQJWKUHVKROGYDOXH¿QHDGMXVWPHQWDQGNH\ORFNIXQFWLRQFDQEHVHW• For setting method of each function, refer to “ 7 TEACHING MODE,” “ 8THRESHOLD VALUE FINE ADJUSTMENT FUNCTION,” or “ 9 KEY LOCKFUNCTION.”• Select either Light-ON or Dark-ON.• For the setting, refer to “ 10 SENSING OUTPUT OPERATION MODE.”• The default setting is “ ” (Light-ON).• An item set in CUSTOM mode is displayed.• For details, refer to “ 11 CUSTOM MODE.”• The default setting is “ ” (response time setting).• Advanced setting can be done.• For the setting, refer to “ PRO MODE.”
|
