Panasonic PHI/TY-LA1000 User Instructions

PPHHII//TTYY--LLAA11000000RREEPPLLAACCEEMMEENNTT LLAAMMPP FFOORR PPAANNAASSOONNIICC LLCCDD RREEAARR PPRROOJJEECCTTIIOONN TTEELLEEVVIISSIIOONNREPLACING THE L AMPU SER INSTRUCTIONSCAUTION:Do not attempt to remove the lamp immediately after use; doing so can cause serious burns. Prior to removing lamp, switch off thepower supply to the television and wait approximately 60 minutes or more to allow for complete lamp cooling.Avoid touching the glass portion(s) of the lamp with bare hands; fingerprints, dirt and dust may cause early lamp failure and/or imageobscurity. It is recommended that gloves be worn when replacing the lamp.When transporting the replacement lamp, use the box that is provided to avoid breakage....To avoid overheating and/or fire, ensure that the replacement lamp is mounted securely.Hg - LAMP CONTAINS MERCURY, Manage in Accord with Disposal Laws. See: www.lamprecycle.org or1-800-555-0050...WARNING:®Switch off power to the television, wait until the powerindicator stops blinking red, then unplug the power cord fromthe wall outlet. Allow the television to cool for at least1 hour.[If the lamp must be replaced more urgently:]The projection display has a feature for forced cooling.During the first minute of the normal cooling fan operationafter the POWER button is turned OFF, press the VOL+button on the projection display and the s button on theremote control simultaneously for more than 5 seconds.The cooling fan will operate for approximately 10 minutes.The LAMP indicator will flash red 5 times every 5 seconds.MODELS PT-50LC13/PT-60LC13/PT-50LCX63/PT-60LCX63/PT-43LCX64/PT-50LCX64/PT-60LCX64/PT-43LC14/PT-50LC14/PT-60LC14POWER button/POWER indicatorLAMP indicatorWARNING : Only reset the lamp timer when the lamp has been replaced.While pressing the VOL- button on the projection display, hold down the PIP or SPLIT button on the remote controlsimultaneously for more than 5 seconds.When the lamp time reset procedure is complete, the above screen will appear. (This screen may be different fromthe actual screen.) Note: When the lamp time reset is complete, the LAMP indicator goes out.sSPLITPLAYLAMP TIME WASRESET TO 0.For models PT-43LC14/PT-50LC14/PT-60LC14For models PT-50LC13/PT-60LC13/PT-50LCX63/PT-60LCX63/PT-43LCX64/PT-50LCX64/PT-60LCX54PIPREMOTE CONTROLVOLUNIT+_RESETTING THE LAMP TIMERMODELS PT-50LC13/PT-60LC13/PT-50LCX63/PT-60LCX63/PT-43LCX64/PT-50LCX64/PT-60LCX64/PT-43LC14/PT-50LC14/PT-60LC14Plug the power cord back into a properly grounded wall outlet. Then press the POWER button on the projectiondisplay or the remote control to turn the power on.12 OR31Remove the front cover by placing your fingertips under thefront cover and pulling it from the projection display.Front cover2After reading the caution and warning labels on the lampcover, loosen the lamp cover screw using a screwdriver.3Using a screwdriver, loosen the lamp unit screw. Graspthe lamp unit handle and slowly pull the lamp unit from theprojection display.4Insert the new lamp unit, paying attention to the direction ofinsertion. Press on the lamp unit handle, ensuring that theinsertion is done correctly. Dispose of the old lamp in accor-dance with disposal laws. Tighten the lamp unit screw and thelamp cover screw using a screwdriver. Replace front cover.[Note: Ensure that the lamp unit and lamp unit housingdoors are attached securely. If not, the protective circuit willbe activated and the power will not turn on.]5Lamp UnitScrewLamp UnitHandle

/ 2

Related manuals for Panasonic PHI/TY-LA1000