Panasonic PT-EX12K Brochure
Also see for PT-EX12K: Dimensional drawing
      | |
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.Product availability differs depending on region and country. This product may be subject to export control regulations.The projection distances and throw ratios given in this brochure are for use only as guidelines. For more detailed information, pleaseconsult the dealer from whom you are purchasing the product. The PJLink trademark is an application trademark in Japan, theUnited States, and other countries and regions or registered trademarks. All other trademarks are the property of their respectivetrademark owners. Projection images simulated.© 2012 Panasonic Corporation. All rights reserved. PT-EX16KG2 Printed in Japan.All information included here is valid as of February 2012.*1 The values given for the recommended lamp replacement cycles are maximum. *2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.*3 The ET-ELW06 is equipped with only vertical optical axis shift. *4 Compliant with VESA CVT-RB. *5 This port is for use by service personnel only. The USB interface may not operate with all USB compatible equipment.Specificationshttp://panasonic.net/avc/projectorFor more information about Panasonic projectorsDo not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, malfunction or electric shock.Caution1 This product must not be used in residential areas.2 This product may cause interference if used in residential areas. Such use must be avoided unless the user takesspecial measures to reduce electromagnetic emissions to prevent interference to the reception of radio andtelevision broadcasts.3 The projector uses a high-voltage mercury lamp under high internal pressure. This lamp may break, emitting apopping sound, or fail to illuminate, due to impact or extended use.4 The high-wattage lamp becomes very hot during operation. Please observe the following precautions:• Never place objects on top of the projector while it is in operation. • Make sure there is an unobstructed space of1,000 mm (39-3/8 in) or more around the projector’s exhaust openings. • If stacking projector units, care must betaken to provide the recommended space between units. These space requirements also apply to installationwhere only one projector unit is operating at one time and the other unit is used as a backup. • If the projector isplaced in a box or enclosure, the temperature of the air surrounding the projector must match the operatingtemperature listed in the specifications table during use. Also, make sure the projector’s intake and exhaustopenings are not blocked. Ensure there is sufficient ventilation to prevent hot air from the exhaust openings beingrecirculated into the intake opening.5 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.• The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions.• The brightness of the lamp will gradually decrease with use.6 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lampperformance.NOTE ON USEModel PT-EX16K PT-EX12KPower supply 200-240 V AC, 50/60 Hz 100-240 V AC, 50/60 HzPower consumption 1,850 W (18 W with standby mode) 940 W (17 W with standby mode)LCD panelPanel size 46 mm (1.8 inches) diagonal (4:3 aspect ratio)Display method Transparent LCD panel (x 3, R/G/B)Pixels 786,432 (1,024 x 768) x 3, total of 2,359,296 pixelsPixel configuration StripePure color control device 1Lens OptionalLamp 380 W x 4, lamp replacement cycle (lamp power:Normal/Eco1, Eco2): 2,000 hours/3,000 hours*¹380 W x 2, lamp replacement cycle (lamp power:Normal/Eco1, Eco2): 2,000 hours/3,000 hours*¹Screen size (diagonal) 1.02–15.24 m (40–600 inches) (2.54–15.24 m [100–600 inches] with the ET-ELS03), 4:3 aspect ratioBrightness*² 16,000 lm (4-lamps, lamp power: Auto/Normal, Optional lens: ET-ELS03) 13,000 lm (2-lamps, lamp power: Auto/Normal, Optional lens: ET-ELS03)Center-to-corner uniformity*² 90 %Contrast*² 2,500:1 (full on/full off, 4-lamps, lamp power: Auto) 4,000:1 (full on/full off, 2-lamps, lamp power: Auto)Resolution 1,024 x 768 pixels (Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.)ScanningfrequencyHDMI/DVI-D Horizontal: 26–80 kHz, vertical: 23–85 Hz, dot clock: 162 MHz or lowerRGB (analog) fH: 15–120 kHz, fV: 48–120 HzDot clock: 230 MHz or lower (Signals exceeding the dot clock rate of 165 MHz are downsampled.)YPBPR (YCBC R)fH: 15.75 kHz, f V: 60 Hz [480i (525i)]fH: 31.25 kHz, f V: 50 Hz [576p (625p)]fH: 33.75 kHz, f V: 60 Hz [1035/60i]fH: 28.13 kHz, f V: 25 Hz [1080/25p]fH: 27.00 kHz, f V: 48 Hz [1080/24sF]fH: 67.50 kHz, f V: 60 Hz [1080/60p]fH: 15.63 kHz, f V: 50 Hz [576i (625i)]fH: 45.00 kHz, f V: 60 Hz [720 (750)/60p]fH: 33.75 kHz, f V: 60 Hz [1080 (1125)/60i]fH: 28.13 kHz, f V: 50 Hz [1080/25sF]fH: 33.75 kHz, f V: 30 Hz [1080/30p]fH: 56.25 kHz, f V: 50 Hz [1080/50p]fH: 31.50 kHz, f V: 60 Hz [480p (525p)]fH: 37.50 kHz, f V: 50 Hz [720 (750)/50p]fH: 28.13 kHz, f V: 50 Hz [1080 (1125)/50i]fH: 27.00 kHz, f V: 24 Hz [1080/24p]fH: 33.75 kHz, f V: 60 Hz [1080/30sF]Video/S-Video fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]Optical axis shiftWith the ET-ELW06: vertical ±39% from center of screen (powered)*³With the ET-ELW02/ELW04/ELS03/ELM01/ELT02/ELT03: vertical ±39%, horizontal ±10% from center of screen (powered)With the ET-ELS02: vertical ±50%, horizontal ±10% from center of screen (powered)With the ET-ELW03: the optical lens shift function cannot be used.Keystone correction range Vertical: Maximum ±40°, Horizontal: Maximum ±40° (with XGA signal input, for vertical/horizontal correction only, Optional lens: ET-ELS03)Installation Ceiling/floor, front/rearTerminalsINPUT1DVI-D INDVI-D 24-pin x 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only), 480p, 576p, 720/60p, 720/50p,1080/60i, 1080/50i, 1035/60i, 1080/24p, 1080/24sF, 1080/25p, 1080/25sF, 1080/30p, 1080/30sF, 1080/60p, 1080/50p,VGA (640 x 480)–WUXGA (1,920 x 1,200)*⁴, compatible with non-interlaced signals only, dot clock: 25–162 MHzHDMI INHDMI 19-pin x 1 (compatible with HDCP, compatible with Deep Color), 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i,1035/60i, 1080/24p, 1080/24sF, 1080/25p, 1080/25sF, 1080/30p, 1080/30sF, 1080/60p, 1080/50p,VGA (640 x 480)–WUXGA (1,920 x 1,200)*⁴, compatible with non-interlaced signals only, dot clock: 25–162 MHzANALOG IN D-sub HD 15-pin (female) x 1 (RGB x 1)INPUT2RGB 5BNC IN/VIDEO IN BNC x 5 (RGB/YPBPR/YCBCR x 1), shared with VIDEO IN (BNC x 1) (composite video)S-VIDEO IN Mini DIN 4-pin x 1 (S-Video)INPUT3/INPUT4Optional interface board slot, When the ET-MD16SD1 is installed,SERIAL IN (SDI IN 1/2): BNC x 2 (SD-SDI signal/single link HD-SDI signal)SD-SDI signal (YCBCR 4:2:2 10-BIT): 480i, 576i (SMPTE 259M-C compliant)Single-link HD-SDI signal (YPBPR 4:2:2 10-BIT): 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/25sF,1080/24p, 1080/24sF, 1080/30p, 1080/30sF (SMPTE 292M compliant)SERIAL OUT (SDI OUT): BNC x 1 (active through)SERIAL IN D-sub 9-pin (male) x 1 for external control D-sub 9-pin (female) x 1 for external controlSERIAL OUT D-sub 9-pin (male) x 1 for link controlREMOTE IN M3 Jack x 1 (for wired remote control)LAN RJ-45 x 1 (for network connection, 100Base-TX/10Base-T, compliant with PJLink™ [class1])USB USB type-B (USB connector) x 1*⁵Cabinet materials Molded plasticDimensions (W x H x D) 650 x 349 x 815 mm (25.6” x 13.7” x 32.1”)(with legs at shortest position, optional lens not included)538.5 x 268 x 757 mm (21.2” x 10.6” x 29.8”)(with legs at shortest position, optional lens not included)Weight Approximately 46.5 kg (102.5 lbs) (optional lens not included) Approximately 28 kg (61.7 lbs) (optional lens not included)Noise level 51 dB (lamp power: Normal/Eco2), 48 dB (lamp power: Eco1) 42 dB (lamp power: Normal/Eco2), 39 dB (lamp power: Eco1)Operating temperature 5°C- 40°C [41°F-104°F] (less than 1,800 m [5,906 ft] above sea level),5°C- 30°C [41°F-86°F] (between 1,800 m and 2,700 m [5,906 ft to 8,858 ft] above sea level)0°C- 40°C [32°F-104°F] (less than 1,400 m [4,593 ft] above sea level),0°C- 30°C [32°F-86°F] (between 1,400 m and 2,700 m [4,593 ft to 8,858 ft] above sea level)Operating humidity 20–80 % (no condensation)Supplied accessoriesPower cord x 1 (x 2 for PT-EX16KE/EX12KE), power cord holder/power cord cover x 1set, wireless/wired remote control unit,batteries (AAA/R03/LR03 type x 2), VGA cable x 1, software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software,Real Color Manager Pro.), lens attachment x 1set, lens lock lever fixing bracket x 1set, lightshielding plate x 3set, spacer x 1set, cable tie x 3 |
Related manuals for Panasonic PT-EX12K
manualsdatabase
Your AI-powered manual search engine