Panasonic SA-PM4E Service Manual

Pin No. Mark I/O Function1 IN2 I Motor Driver Input2 PC2 I Turntable Motor Drive Signal(“L”:ON)3 IN1 I Motor Drive (1) Input4 PC1 - Traverse Motor Drive Signal(“L”): ON)5-8 N.C. - No Connection9 PGND1 - Ground Connection (1) for Drive10 PVCC1 - Power Supply (1) for Drive11 D1- O Motor Drive (1) reverse - actionoutput12 D1+ O Motor Drive (1) forward - actionoutput13 D2- O Motor Drive (2) reverse - actionoutput14 D2+ O Motor Drive (2) forward - actionoutputPin No. Mark I/O Function1 PCONT1 O Power Control Output 1(PwrSply,Active HIGH)2 PCONT2 - No Connection3 NC - No Connection4 FL_DATA /OCD_SDAI FL Data Output / On ChipDebugger Data5 NC - No Connection6 FL_CLK /OCD_SCLI FL CLK Output / On ChipDebugger Clock7 NC - No Connection8 NC - No Connection9 NC - No Connection10 NC - No Connection11 MMOD - Memory mode selection12 OSC2 (8MHz) O Main Oscillator output (8MHz)13 OSC1 (8MHz) I Main Oscillator input (8MHz)14 VSS - Micom GND15 XI (32KHz) I Slow Oscillator input (32KHz)16 XO (32KHz) O Slow Oscillator output (32KHz)17 3.3V - Voltage supply 3.3V18 Internal Output(1.8V)- Connect to pin 3719 NRST I/O MICOM RESET PIN (L: reset)20 NC - No Connection21 NC - No Connection22 NC - No Connection23 NC - No Connection24 DAB_PCONT - DAB module power control25 RMT I Remote Control Input26 NC - No Use27 DAB_DDOWFICI DAB LSI 24ms synchronizationinterrupt28 DAB_IRQ I DAB LSI interrupt (currentlyunused)29 BLKCK I CD Subcode Block Clock Input30 VCCDET I VCC Failure Detect Signal ("L"when AC in)31 CD_MDATA I/O CD LSI Command Data32 STAT I CD LSI Status Input33 CD_MCLK I CD LSI Command Clock34 N.C. - No Connection35 CD_MLD O CD LSI Command Load36 N.C. - No Connection37 1.8V - Power Supply (1.8V)38 MUTEA O Analog MUTE Output(L:MUTEON)Pin No. Mark I/O Function15 D3- O Motor Drive (3) reverse - actionoutput16 D3+ O Motor Drive (3) forward - actionoutput17 D4- O Motor Drive (4) reverse - actionoutput18 D4+ O Motor Drive (4) forward - actionoutput19 PVCC2 - Power Supply (2) for Driver20 PGND2 - Ground Connection (2) for Driver21-24 N.C. - No Connection25 VCC I Power Supply terminal26 VREF I Reference Voltage Input27 IN4 I Motor Driver (4) Input28 IN3 I Motor Driver (3) InputPin No. Mark I/O Function39 VSS - Micom GND40 ASP_CLK O ASP Sound Processor SerialClock Output41 ASP_DATA O ASP Sound Processor SerialData Output42 NC - No Connection43 NC - No Connection44 NC - No Connection45 CD_RST O CD LSI Reset Ouput (L: reset)46 N.C. - No Connection47 Demo_Set I Demo Mode Setting Input48 MODEL_SEL - Model Select (H: PM4, L: PM45)49 PLL_DO O Data out for Tuner (PLL DataI/O)50 PLL_DI I Data in for Tuner (PLL Data I/O)51 PLL_CLK - Clock for Tuner (PLL ClockOutput)52 VOL_JOG1 I Jog Input 153 VOL_JOG2 I Jog Input 254 PLL_CE O Tuner Tuned Signal55 N.C. - No Connection56 N.C. - No Connection57 N.C. - No Connection58 N.C. - No Connection59 N.C. - No Connection60 MBP1 I/O Microp-beatproof61 MBP2 I/O Microp-beatproof62 CRTIMER - CRTIMER63 VSS - Micom GND64 FL_STROBE - Chip select for FL Panel65 N.C. - No Connection66 N.C. - No Connection67 N.C. - No Connection68 N.C. - No Connection69 N.C. - No Connection70 N.C. - No Connection71 N.C. - No Connection72 N.C. - No Connection73 RDS_DATA I RDS Data Input74 RDS_CLK O RDS Clock Input75 N.C. - No Connection76 N.C. - No Connection77 N.C. - No Connection78 N.C. - No Connection79 N.C. - No Connection80 N.C. - No Connection18.2. IC7002 (BA5948FPE2) IC 4CH Drive18.3. IC800 (MN101EF16ZXW) MICROPROCESSOR59SA-PM4E / SA-PM4EB / SA-PM4EG