Panasonic SL-CT830 Operating Instructions Manual

Contents

4MP3You cannot select “RND” and “AB” with MP3.Handy functionsPlayback modesWhen the display is difficult to see...(Contrast adjustment)(On the main unit)Set the main unit to HOLD while stopped. While pressing and holding[/], press [] (darker) or [] (lighter).To see the display in the darkEach time you change the position of the hold switch on the remotecontrol, the display will light for approx. 5 seconds.EQ If you select 3D-1 or 3D-2, the sound volume may be reduced.The effect may differ with different kinds of music.Depending on the recording conditions, sound may be interruptedwhen switching between EQ settings.If you select 3D-1 or 3D-2 then try playing a disc that contains both CD-ROMformat and CD-DA format tracks, there will be a brief noise when the discchanges from playing the CD-ROM format track to the CD-DA format one.If RMTR is set when playing MP3, the effect is canceled as soon as aCD-DA format track is played.MODE RND RND A1 BOne trackrepeatAll trackrepeatRandom RandomrepeatNo display (canceled)AB repeat(Dbelow)While playingWhile pausedor “~” is displayed in place of anything over 32 characters. “_” is displayed in place of characters this unit cannot display. “ ” appears if ID3 tags haven’t been entered.MEMO/DISPRQT8183Track titleID3 track titleTrack number andelapsed play timeAlbum titleID3 artist nameMP3 and CD-DA indicatelimitations on these discs only.Changing the play mode Changing the sound quality/sound effectsChanging the display MP3 While stopped, tilt to selectthe track number.MEMO/DISPPress to enter.Track number01 M ALBUM13 MSequence number Album numberMP3013 MTrack number Sequence numberWill appear after[MEMO/DISP] is pressedCD-DA Repeat steps to to program up to 20 tracks. Press to play.Confirm tracks selected: While playing, press [MEMO/DISP].Cancel: While playing, press [/] (Remote control)./Press [] (Main unit).(“M” disappears.)Playing desired tracks only (Program play)MODE To select another album (Dpage 3, Album skip) You cannot select album mode during program play (Dabove).Each time you press and holdNo display(canceled)Album mode(Only tracks on the desiredalbum are played)H.BASSH.BASSS-XBSS-XBSTRAINBoosts the bassReduces sound leaksand listening fatigueEnhanced S-XBSNo display (Cancels thesound quality)Enhanced H.BASSAdd powerful bassMP3 RMTR (Digital Re-master):You can regenerate signal frequencylost during compression, restoring thesound to near pre-compression form.While playing, each timeyou pressWhile playing, each timeyou press and holdChanging the sound quality Changing the sound effectsSound field of 3D3D-13D-2RMTRMP3Enhanced 3D-1More naturalsound qualityNo display (Cancels thesound effect)The anti-skip function (ANTI-SKIP SYSTEM) reduces or eliminates skippingcaused by vibration. You can change the anti-skip memory time.MEMO/DISPPOS2 POS1Anti-skip enhanced modeAble to withstand a maximum of45 seconds of vibrationSound enhanced modeAble to withstand a maximum of10 seconds of vibrationMP3 You cannot change the memory time for MP3. It is a maximumof 100 seconds for MP3 recorded at 128 kbps.Changing the anti-skip mode CD-DAWhile stopped,each time you press and holdWhile playing, each timeyou press and holdTurn off this unit and the other equipment before connection.Insert each plug fully. (Plug type: 3.5 mm stereo)If you don’t want the remote control operation tone, turn it off (Dpage 3).Each time you pressTo CD or AUXterminalsAudio systemand so onMain unitRemotecontrolAudio cable (not included)You cannot use anoptical cable.Specifying the AB segmentPress to specify the start point (A).Press once more to specify the end point (B). Stop or skip (Dpage 3) to cancel. If you do not specify point B this will automatically be set as theend of the disc. Repeat begins when this point is reached. You canalso specify point B again by pressing [MEMO/DISP].MEMO/DISPMP3 and CD-DA indicatelimitations on these discs only.You can combine the sound quality and sound effects settings. Set thesound quality by pressing [EQ] and then the sound effects by pressingand holding [EQ]. (You can also set the sound effects first.)When connecting the unit to other equipment, set the volumelevel between 10 to 15, then use the volume control on the otherequipment to adjust the volume.Connecting to other equipmentPlaying only the tracks in a selected album(Album mode) MP3(backward) (forward)

/ 4

Related manuals for Panasonic SL-CT830