Panasonic TY-WK42PV4W Installation Instructions Manual

Also see for TY-WK42PV4W: Service manual

Contents

Panasonic TY-WK42PV4W Installation Instructions Manual Manual pdf 4 page image

4 English Fitting procedure [ Never use any other methodthan specified to install.]1. Confirm the strength of the proposed fitting location.(1) The weight of the wall-hanging bracket is approximately 7 kg (15.4 lbs). For the weight of theplasma TV attached to the wall-hanging bracket, please see manual for the plasma TV.(2) Check the wall strength at the 6 attachment locations by referring to the dimension drawingof the wall-hanging bracket (given at right), and provide adequate reinforcement if strengthis not sufficient.Notes• There are 22 holes in the wall-hanging bracket.If the wall material is wood, and adequate attachment strengthcannot be ensured by fastening at the 6 points at right, useas many spare holes as necessary. However, exercise carebecause some wall materials may crack if screws are locatedtoo close together.The following dimensions are important. Do not fit at anylocation where these dimensions cannot be secured.• For detailed dimensions for attaching the plasma TV, refer tothe separate External Dimension Drawing (page 46-48).• Do not attach or place anything other than the plasma TV onthe bracket.100100100(3.9)320 (12.6)11 (0.4)415 (16.3)B370 (14.6)23(0.9)775 (30.5)A735 (28.9)660 (26.0)195(7.7)416 (16.4)Unit: mm (inches)* Be sure to fit screws and tighten securely.Wall-hanging bracket Wall attachmentholes (at 6 points)Plasma TV external profile* Provide spacing around the plasma TV of at least 10 cm(3.9″) to the top and right side, at least 30 cm (11.8″) tothe left side, at least 6 cm (2.4″) to the bottom, leave aclearance between the rear panel and the wall.2. Fit wall-hanging bracket to wall.(1) Fit so that the arrow marks on the wall-hanging bracket point upward.(2) Fasten the screw at the top center hole (A) first.(3) Using a level, correct any bracket inclination, and then fasten screws at the remaining5 locations.(A)Notes• If the wall consists of a material such as concrete, and bolts or nuts must be embeddedbeforehand, determine the hole positions using the actual wall-hanging bracket, orcalculate hole positions based on the dimension drawing and then embed bolts ornuts with a nominal diameter of 6 mm. When embedding bolts, locate so that the boltsprotrude from the wall by 10 to 15 mm (25/64 to 19/32 inches).• Use commercially available screws with a nominal diameter of 6 mm that are suited tothe wall material you are fitting the bracket to.• Always fix firmly more than 6 places with a screw.3. Fit the insulation spacers to the plasma TV.(1) Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow theprocedure below.(2) Remove terminal covers (if fitted) from the plasma TV.(3) Using a flathead screwdriver, remove the four caps from the plasma TV.Note• Carefully retain the removed terminal cover and caps in a safeplace. (They will be needed again later should it be requiredto use the special-purpose stand or standalone stand.)Terminal coverCapsFlathead screwdriverCloth㇜㇞ or ㇟㇛㇚(4) Using the included Allen wrench ㇜ , fit the included Allenhead countersunk screws ㇞ or ㇟ dished toothed washers㇛ and insulation spacers ㇚ (4 sets) into the holes fromwhere the caps were removed. (See the diagram at right.)Refer to the page 46-48 for details on selecting thehexagon flat countersunk head screws ㇞ or ㇟ .The bolt should be securely tightened to the torque givenbelow.(11 - 13 N•m)