Panasonic Viera TX-32LXD700A Operating Instructions Manual

Also see for Viera TX-32LXD700A: Brochure & specs

Contents

AdvancedOPTIONMULTI PIPPOWERSD CARDASPECTF.P.VOLRECALL MUTECHGR Y BEXITRETURNINPUTMain MenuVIERA LinkPictureSoundSetup1/2Tuning MenuOff Timer OffShipping ConditionAccessSetup MenuTeletext TOPSystem UpdateInput LabelsDVB Favourites Edit3 secondsVIERA Link SettingsBanner Display TimeoutTuning MenuAuto Tuning AccessAnalogue Programme Edit AccessDVB Manual TuningAnalogue Manual Tuning AccessAdd New DVB Services AccessAccessNew Service MessageDVB Signal Display AccessOn24 25Editing and Setting ChannelsThe current channel settings can be changed according to your needs and reception conditions.You can re-tune all TV channels when moving house or search for new services which may haverecently started broadcasting.• Editing and Setting Channels■ To return to TVEXITEditAnaloguechannelsRATING: PG Bad Signal Dolby D 45TEXTSTTLNow9:00 am - 11:00 am1 TEN 10:30 amCorontation Street Select FAV ListAll Analogue ServicesAnalogue Programme Edit1 CH332 CH213 CH214 CH605 CH21Prog. Chan. Name1 2 3X Y ZF T P4 5 6OffOffOffOffOffSkipAnalogue Programme Edit1 CH332 CH213 CH214 CH605 CH21Prog. Chan. Name1 2 3X Y ZF T P4 5 6OffOffOffOffOffSkip■ To change the name of the broadcasterdisplayed when selecting channelsCursorSelect the channel to editEdit■ To delete RAfter confirming, press R■ To add GAfter confirming, pressG■ To move YSelect new positionYEdit the analogue programme position settingsselect( Maximum: five characters)Analogue Programme Edit1 CH332 CH213 CH214 CH605 CH21Prog. Chan. Name1 2 3X Y ZF T P4 5 6OffOffOffOffOffSkip Select the“Skip” fi eldSelect“On”■ To skip the channel• This function is only effective whenpressing the Programme Up / Downbutton on the TV or the remote control.ChannelNameSelect the“Name” fieldSelect thecharacterSetR Enter the “Userinput” mode• To change channel number“Analogue Manual Tuning”RETURNStore■ Delete■ Add■ Move■ Changename■ SkipAnalogueProgrammeEditSet6Select “Setup”3Select “Tuning Menu”4Display the menuSelect a function521 Select DVB or Analogue• “DVB Manual Tuning”, “Add New DVB Services”, “New ServiceMessage” and “DVB Signal Display” are available in DVB mode only.• “Analogue Programme Edit” and “Analogue Manual Tuning” areavailable in Analogue mode only.Auto Tuning - Digital (DVB) and AnalogueThis will take about 3 mins.Analogue Tuning 0 75Digital (DVB) Tuning 6 692RF Ch Service Name Type QualityABC TV Sydney DVB 103 SBS DIGITAL 1 DVB 104 FTV guide DVB 107 7 Digital DVB 109 NINE DIGITAL DVB 10CH 29 Analogue -CH 33 Analogue -EXITRETURNStart Auto TuningAnalogue & DVB tuning data will be erasedAuto TuningAccess “Auto Tuning” Settings are made automaticallyAutomatically set the DVB and Analogue channels received in the area.• All previous settings are erased.• When the operation is completed, the digital service at programme position “1” will be displayed.If no DVB services are found, the first analogue service will be displayed.• If tuning has not done completely “DVB Manual Tuning”, “Analogue Manual Tuning”Set channelsautomaticallyAutoTuningDVB Signal DisplayService Name [CH53] 7 7 Digital0 5 10Signal QualitySignal StrengthSelects a service and checks the DVB signal condition.Use for adjusting the direction of the aerial.Signal Quality:• Green bar Good• Yellow bar Poor• Red bar Bad (Check the aerial)• To change the service during the menu appears CHCheckDVB signalDVB SignalDisplayDisplay anotificationmessageNew ServiceMessageNew DVB service found!Press OK to add new service.Press EXIT to lgnore.Selects whether to give a notification message when a new DVB service is found. (Off / On)Normally use “Auto Tuning” or “Add New DVB Services” for the DVB channel setting.If tuning has not done completely, use this function.Set DVBchannelmanuallyDVB ManualTuningadjust frequency( set where the level of “Signal Quality”becomes the maximum)select channelsearchDVB Manual TuningSignal Quality 0 10Signal Strength 0 10Physical Channel MHz[CH21] 474.00Prog. RF Ch Net ID. QualityTS ID.Service NameAddDVB channelautomaticallyAny new services found will be added automatically.Add New DVB ServicesPlease wait!This will take about 3 mins.6 69Prog. RF Ch Service Name Net ID. TS ID. QualityZDFARD• The new service is added with the current settingssaved as they are.Add NewDVB ServicesProgramme 1 [CH33]Analogue Manual TuningManual Tuning 0 75Set AnaloguechannelmanuallyAnalogueManual TuningSet Analogue channel manually after Auto Tuning.If a VCR is connected with only the RF cable, select programme position “0”.storesearchSearch and storeSelect the channelCHSelect the programme positionFor Auto Tuning, using the buttons on the top of the TV F TV AVPress repeatedly until “Auto Tuning” appears FAccess “Auto Tuning” TV■ To return to TV FStart “Auto Tuning” TVaccessselectaccessselectaccessselect