Panasonic WJ-FS616 Operating Instruction

Also see for WJFS616 - SWITCHER: Operating instructions Service manual

-31-SEQ1(SPOT-SEQUENCE)SETUP 1 OF 2AUTO SKIP OFFDWELL TIME 2SECSTEP CAM PRE TIME STEP CAM PRE TIME1 1CH - 2SEC 9 9CH - 2SEC2 2CH - 2SEC 10 10CH - 2SEC3 3CH - 2SEC 11 11CH - 2SEC4 4CH - 2SEC 12 12CH - 2SEC5 5CH - 2SEC 13 13CH - 2SEC6 6CH - 2SEC 14 14CH - 2SEC7 7CH - 2SEC 15 15CH - 2SEC8 8CH - 2SEC 16 16CH - 2SECPress the FUNCTION button to display the nextpage, then press this button again to return tothe previous page.2. Move the cursor to the channel you want toedit, then press the SET button.The cursor moves to the title area, and the squarecursor appears on the character table.3. To select a character, move the cursor on thedesired character in the table by pressing theDirection Arrow buttons.4. Then press the SET button to pick up the char-acter, and place it in the title area.5. Repeat the above procedures 3 to 4 until thetitle for a certain camera is completed.6. If a wrong character is selected, press theIncrement (+) or Decrement (−) button to movethe cursor in the title area.Note: Press the (+) button to move the cursorto the right, or press the (−) button to movethe cursor to the left.Then press the SET button to overwrite thecharacter with the character selected inthe table.7. Press the SETUP/ESC button to move the cur-sor to the channel number area.8. Repeat the above procedures 2 to 7 for therest of the cameras.9. Move the cursor to the channel area, thenpress the SETUP/ESC button to return to theprevious SYSTEM SETUP menu.4. Camera Title Display PositionThis item lets you select the camera title position tobe displayed on the Spot Monitor screen.Refer to the Clock Position Setting on page 30 formore details.1. Move the cursor to TITLE POSITION, thenpress the SET button. The position settingmenu appears on the monitor screen.2. Move the title by pressing the Direction ArrowButtons.Note: The camera title and the clock are dis-played on the same line of the Spot moni-tor.If the camera title position is moved toupward or downward, the clock is movedto that position at the same time.3. Press the SETUP/ESC button to execute theselection and return to the previous SYSTEMSETUP menu.5. Sequence SetupThis item lets you program the sequence patternfor Spot or Multi Sequence.You can either program a spot sequence (SEQ1) ortwo multi sequences (SEQ2, SEQ3).l Spot Sequence (SEQ1)This item lets you program or edit a SpotSequence. Up to 32 steps can be assigned in thetable shown below.You can also enable the Auto Skip function to skipany steps where no video signal is present.The duration of each step is determined by theDwell Time setting.Initially, it is selected at the factory that 16 camerapictures are displayed in succession.1. Move the cursor to the SEQUENCE SETUPparameter on the SYSTEM SETUP menu.2. Select SEQ1 by pressing the LEFT or RIGHTbutton, then press the SET button. The setupmenu shown below appears on the monitorscreen.Auto Skip1. Move the cursor to the AUTO SKIP parameter.2. Select ON or OFF by pressing the LEFT orRIGHT button.ON: Enables the auto skip function.OFF: Disables the auto skip function.Step Assigment1. Move the cursor to the step number you wantto edit in the CAM area by pressing theDirection Arrow button.2. Select the desired camera or playback channelin the CAM area by pressing the Increment (+)or Decrement (−) button.1 - 16: Camera ChannelP1 - P16: Playback Channel–: Not AssignedNote:Any playback steps programmed in asequence are excluded from display onthe Spot Monitor and Multiscreen 2 Monitordue to the way te system is designed.3. Repeat the above procedures to assign othersteps.