Panasonic WV-CF364E Operating Instructions Manual
Use this product for indoor use only.Do not expose this product to direct sunlight forhours and do not install the product near aheater or an air conditioner, otherwise it maycause deformation, discolouration and malfunc-tion. Keep this product away from water.Avoid installing in the following locations.• Locations where it may get wet from rain orwater splash• Locations where a chemical agent is usedsuch as a swimming pool (not only outdoor)• Locations subject to steam and oil smokesuch as a kitchen• Locations near flammable gas or vapor• Locations where radiation or x-ray emis-sions are produced• Locations subject to strong magnetic fieldor radio waves• Locations where corrosive gas is produced• Locations where it may be damaged bybriny air such as seashores• Locations where the temperature is notwithin –10 °C - +50 °C .• Locations subject to vibrations (this prod-uct is not designed for on-vehicle use.)Installing placeContact your dealer for assistance if you areunsure of an appropriate place in your particu-lar environment.Do not install this product in a humid ordust-laden environment.Otherwise, lifetime of the internal parts may beshortened.Be sure to remove this apparatus if it is notin use.Radio interferenceWhen the product is used near TV/radio anten-na, strong electric field or magnetic field (neara motor or a transformer), images may be dis-torted and noise sound may be produced.Mounting screwsIt is necessary to procure screws or bolts tomount the product. Prepare them according tothe material and strength of the area where thecamera is to be installed. The screws and boltsmust be tightened with an appropriate tighten-ing torque according to the material andstrength of the installation area.Major Operating Controls and Their Functionsq Video output connectorComposite video signals are transmitted. Ifthis unit is connected to the multiplex unit,the multiplexed VD2 that is prioritized overINT is automatically selected.w MarkerThis marker is used when the top cover isinstalled.e Dip switchSelects ON/OFF of white balance, backlightcompensation, Adaptive Black Stretch orday/night mode.• Day/night mode selector [D/N]ON: The camera selects black-and-whitemode if the picture is dark, or colormode if the picture is bright enough.Switches from color to black-and-whiteimages when the ambient brightness(illuminance) of the camera is approx.0.6lx or less.OFF: Color picture is displayed normally.Default setting: OFFNote:• To obtain color images, a sufficientlevel of illuminance (approx.30 lx ormore) is required.• The switching illuminance level varieswith subjects,light sources.• The switching illuminances describedabove are reference values. Theswitching illuminance shall be decidedbased on the actual installation envi-ronment.• Adaptive Black Stretch selector [B.S.]ON: The dark area of the object is auto-matically corrected to lighten it.OFF: Does not compensate.Default setting: ONImportant:In the case of "ON" setting, noise maybe increased in the dark area of theobject.In addition, darkness and brightnessmay be emphasized in the vicinity ofthe boundary between the dark andbright areas.• Backlight compensation selector [BLC]ON: Compensates the background auto-matically if it is brighter than theobject.OFF: This mode is used when the front ofthe object is extremely bright.Default setting: OFFNote:Under some conditions, such asextremely strong backlight, the desiredcompensation effect may not beachieved even if the mode is set to ONto detect the backlight level.• White balance selector[ATW/AWC]ATW: Activates the automatic color tem-perature tracking mode. The cameracontinuously measures the color tem-perature of the light source and auto-matically adjusts the white balance.The adjustment of the color tempera-ture ranges from approx. 2 700 K to6 000 K.AWC: Activates the automatic white bal-ance control mode. This adjustment issuitable for a location where a lightsource is stable. The adjustment of thecolor temperature ranges from approx.2 000 K to 10 000 K.Default setting:ATWr Focus lock leverFixes the focus position after adjusting.t Zoom lock leverFix the zoom position after adjusting.y Azimuth adjusterAdjusts the azimuth angle of the camera.u Tilting tableAdjusts the tilting position of the camera.i Panning tableAdjusts the panning position of the cam-era.o Panning table lock screw [LOCK]Fixes the panning table.!0 Power cableSupplies 24 V AC or 12 V DC from an exter-nal power source.!1 Tilting lock screws (left,right)Fixes the tilting position.!2 Monitor output jack (RCA jack)Connects the LCD monitor and suchdevices for checking images.Installations and Connectionsrear● Using a two-gang junction boxWhen using a two-gang junction box (4"x4"),procure one locally that meets the dimensionsin the figure.Next locally procure four camera mountingscrews suitable for the installation surface andstructure of the wall/ceiling or two-gang junc-tion box.Processed section of the sidesurface of the cover■ Disassembling the Camera1. Peel off the protection sheet from thetop cover.Don't remove completely as this protectsthe dome during installation.● To mount the camera on a two-gangjunction box1. Install the two-gang junction box onto thewall/ceiling.2. Mount the camera onto the two-gang junc-tion box with 4 screws (procured locally).3. Fasten all of the mounting screws.Camera mounting screw x4 (not supplied)The mounting requirements are shown as follows.MountingplaceCeiling/wallModel(Direct mounting)Recommended screw andtightening torqueM4,1.6N·m {16 kgf·cm}Number ofscrews4 pcs.Minimum pulloutstrength196 N/pc.{20 kgf/pc.}Ceiling WV-Q168(Approx.280 g) - - **Make sure that the installed mount bracket can support more than 5 times of the weight of thecamera.Top cover fixing screw (M3)The following installation should be made by qualified service personnel or system installers.■ PreparationsImportant:• Procure 4 mounting screws according to the material of the installation area. In this case, woodscrews and nails should not be used.Recommended tightening torque is as follows:M4: 1.6 N·m {16 kgf·cm}• Required pull-out capacity of a single screw/bolt is 196 N {20 kgf} or more.• If a ceiling board such as plaster board is too weak to support the total weight, the area shall besufficiently reinforced.• The protection sheet attached to the dome cover should be peeled off after installation.● Direct mountingIf the camera is directly mounted on a wall/ceil-ing, align the camera mounting position with theposition of the hole through which the cablesrun and make the hole.If no hole is made through a wall/ceiling andopen wiring along a wall/ceiling is used, pleaseremove the dust guard cap,take out thecable,don't forget put back the dust guardcap.Then process the cover so that the cablescan be run through the side of the cover.2. Remove the top cover.• Screw off the screw for fixing the top cover.• Adjust the marker on this unit to "I" on thetop cover, and turn the top cover counter-clockwise to remove it.• The clear dome cover and the inner domecover are joined into a single unit.Therefore, never try to remove them.● To mount the camera directly on thewall/ceiling1. Prepare the mounting space.2. Place the camera onto the wall/ceiling andmark four screw positions with a pen.3. Mount the camera onto the wall/ceiling with 4screws (procured locally).4. Fasten all of the mounting screws. |
Related manuals for Panasonic WV-CF364E
Panasonic WV-CF334E Operating Instructions Manual
Panasonic WV-CF324 Operating Instructions Manual
Panasonic WV-CF344 Operating Instructions Manual
Panasonic WV-CF20 Operating Instructions Manual
Panasonic WV-CF20 Operating Instructions Manual
Panasonic WV-CF250 Operating Instructions Manual
Panasonic WV-CF400 Operating Instructions Manual
Panasonic WV-CF254 Operating Instructions Manual
Panasonic WV-CF212 Operating Instructions Manual
Panasonic WV-CF212 Operating Instructions Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine