Panasonic WV-CP230 Operating Instructions Manual

Also see for WVCP230 - CCD 120V: Operating instructions Specifications Operating instructions Operating instructions Operating instructions

Panasonic WV-CP230 Operating Instructions Manual Manual pdf 1 page image

1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) Automatic Gain Control (AGC) +15 dBand Automatic Tracing White Balance(ATW)(3) Camera synchronization mode selec-table between internal (INT), Line-locked(LL) and Multiplexed Vertical Drive (VD2)for WV-CP230 and WV-CP234.FEATURES2. Minimum illumination of 0.6 lx (0.06 foot-can-dle) at F0.75 (equivalent to 2.0 lx (0.2 foot-candle) at F1.4)3. Signal-to-noise ratio of 50 dB4. Horizontal resolution of 480 lines5. Auto iris lens control selectable betweenvideo signal and DC power supply.1. Do not attempt to disassemble the camera.To prevent electric shock, do not removescrews or covers.There are no user serviceable parts inside.Ask a qualified service person for servicing.2. Handle the camera with care.Do not abuse the camera. Avoid striking,shaking, etc. The camera could be damagedby improper handling or storage.3. Do not expose the camera to rain ormoisture, or try to operate it in wet areas.Turn the power off immediately and ask aqualified service person for servicing.Moisture can damage the camera and alsocreate the danger of electric shock.4. Do not use strong or abrasive detergentswhen cleaning the camera body.Use a dry cloth to clean the camera whendirty.In case the dirt is hard to remove, use a milddetergent and wipe gently.5. Clean the CCD faceplate with care.Do not clean the CCD with strong or abrasivedetergents. Use lens tissue or a cotton tippedapplicator and ethanol.6. Never face the camera towards the sun.Do not aim the camera at bright objects.Whether the camera is in use or not, neveraim it at the sun or other extremely brightobjects. Otherwise, blooming or smear maybe caused.7. Do not operate the camera beyond thespecified temperature, humidity or powersource ratings.Use the camera under conditions where tem-perature is between –10°C - +50°C (14°F -122°F), and humidity is below 90 %. Theinput power source is 120 V AC 60 Hz forWV-CP230, 12 V DC for WV-CP232, and 24 VAC 60 Hz for WV-CP234.PRECAUTIONSColor CCTV CamerasWV-CP230/WV-CP232/WV-CP234Before attempting to connect or operate this product,please read these instructions completely.CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK), NO USER SERVICEABLE PARTSINSIDE.REFER SERVICING TO QUALIFIED SERVICEPERSONNEL.The exclamation point within anequilateral triangle is intended toalert the user to the presence ofimportant operating and mainte-nance (servicing) instructions in theliterature accompanying the appli-ance.The lightning flash with arrowheadsymbol, within an equilateral trian-gle, is interned to alert the user tothe presence of uninsulated "dan-gerous voltage" within the product'senclosure that may be of sufficientmagnitude to constitute a risk ofelectric shock to persons.WARNING:TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TORAIN OR MOISTURE.The serial number of this product may be found onthe top of the unit.You should note the serial number of this unit in thespace provided and retain this instruction as a per-manent record of your purchase to aid identificationin the event of theft.Model No.Serial No.SA 1966SA 1965Caution:To prevent fire or electric shock hazard, ULlisted wire VW-1, style 1007 should be usedfor the DC 12 V or AC 24 V Input Terminal.Cautions:• Connect to 12 V DC (10.5 V-16 V) or 24 VAC (19.5 V-28 V) class 2 power supply only.Make sure to connect the grounding lead tothe GND terminal when the power is sup-plied from a 24 V AC power source.• To prevent fire or electric shock hazard, ULlisted wire VW-1, style 1007 should be usedfor the DC 12 V or AC 24 V Input Terminal.VIDEO OUTGNDAC 24V IN1 2VIDEO OUT

DC 12V INVIDEO OUTLL INTELC ALCSOFT SHARPOFF BLC ONDC VIDEOLL INTELC ALCSOFT SHARPOFF BLC ONDC VIDEOELC ALCSOFT SHARPOFF BLC ONDC VIDEOWV– CP230MAJOR OPERATING CONTROLS AND THEIR FUNCTIONSq Auto Iris Lens ConnectorSupplies power and control signals to an autoiris lens (not supplied).w Flange-back Adjusting RingThis ring adjusts the back-focal distance orpicture focus. Rotate this ring clockwise for aC-mount lens or counterclockwise for a CS-mount lens.e Lens (option)r Camera Mounting Screw HoleThis hole is for mounting the camera onto amounting bracket. The camera is originallydesigned to be mounted from the bottom, buta top-mounting type is also available. Tomount from the top, remove the mountadapter from the bottom of the camera byremoving two fixing screws. Attach the mountadapter to the top as shown in the diagram,then mount the camera on the mountingbracket. Make sure that two original screwsare used when mounting the mount adapter;longer type screws may damage inner com-ponents.t Power Cord (only WV-CP230)Connect this power cord to an electrical out-let of 120 V AC 60 Hz.y DC 12 V Input Terminal(DC 12V IN (only WV-CP232))This terminal is for connecting the 12 V DCpower supply cord.u AC 24 V Input Terminal(AC 24V IN (only WV-CP234))This terminal is for connecting the 24 V AC60Hz power supply cord.i Synchronization Mode Selector(INT, LL (only WV-CP230 and WV-CP234))Selects the camera synchronization modefrom internal sync mode (INT) or line-lockmode (LL).INT: Sets to internal 2:1 interlace.LL: Sets to Line-lock mode.o Automatic Light Control/Electronic LightControl Selector (ALC , ELC)Lets you select the mode according to thelens type that is used with this camera.ALC: Select this mode when an auto iris lens(ALC lens) is used with this camera.ELC: Select this mode when a fixed iris lensor manual iris lens is used with this cam-era.!0 Detail/Aperture Level Selector(SOFT/SHARP)The detail/aperture level can be selected withthis selector. Set it to the desired positionwhile observing the picture on the monitor.SHARP: Normal position.SOFT: Select this position when a QuadSystem is connected to this camera.!1 Back Light Compensation Mode Selector(BLC ON, OFF)Lets you select the mode according to theposition of the object and light conditions onthe screen.ON: Select this mode when a strong lightsuch as a spotlight is in the background.OFF: Normal picture.!2 Lens Drive Signal Selector (VIDEO, DC)Lets you select the mode according to thetype of auto iris lens drive signal to be sup-plied to the lens from the auto iris lens con-nector.VIDEO: Select this mode if you are using aauto iris lens that requires a video drivesignal.DC: Select this mode if you are using a autoiris lens that requires a DC drive signal.!3 Video Output Connector (VIDEO OUT)This connector is for connecting with theVIDEO IN connector of the video monitor.Whenever the multiplexed vertical drive (VD2)signal is supplied to this connector, the cam-era synchronization mode is automatically setto Vertical Drive.N1098-0 YWV8QA5102AN Printed in JapanN 30Warning:This equipment generates and uses radio frequen-cy energy and if not installed and used properly,i.e., in strict accordance with the instruction manu-al, may cause harmful interference to radio com-munications. It has been tested and found to com-ply with the limits for a Class A computing devicepursuant to Subpart J of Part 15 of FCC Rules,which are designed to provide reasonable protec-tion against such interference when operated in acommercial environment.For U.S.A

/ 2

Related manuals for Panasonic WVCP230 - CCD 120V