Panasonic WV-CP230 Operating Instructions Manual

Also see for WVCP230 - CCD 120V: Operating instructions Operating instructions Specifications Operating instructions Operating instructions

Panasonic WV-CP230 Operating Instructions Manual Manual pdf 1 page image

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXTCAREFULLY.This appliance is supplied with a moulded three pin mains plug foryour safety and convenience.A 5 amp fuse is fitted in this plug.Should the fuse need to be replaced please ensure that the replace-ment fuse has a rating of 5 amp and that it is approved by ASTA orBSI to BS1362.Check for the ASTA mark H or the BSI mark G on the body of thefuse.If the plug contains a removable fuse cover you must ensure that itis refitted when the fuse is replaced.If you lose the fuse cover the plug must not be used until a replace-ment cover is obtained.A replacement fuse cover can be purchased from your localPanasonic Dealer.IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THESOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULDBE REMOVED AND THE PLUG CUT OFF AND DISPOSED OFSAFELY.THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THECUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.If a new plug is to be fitted please observe the wiring code as shownbelow.If in any doubt please consult a qualified electrician.WARNING: This apparatus must be earthed.IMPORTANTThe wires in this mains lead are coloured in accordance with the fol-lowing code.Green-and-yellow: EarthBlue: NeutralBrown: LiveAs the colours of the wire in the mains lead of this appliancemay not correspond with the coloured markings identifying the termi-nals in your plug, proceed as follows.The wire which is coloured green-and-yellow must be connect-ed to the terminal in the plug which is marked with the letter E or bythe earth symbol I or coloured green or green-and-yellow.The wire which is coloured blue must be connected to the ter-minal in the plug which is marked with the letter N or coloured black.The wire which is colouredbrown must be connected to the ter-minal in the plug which is markedwith the letter L or coloured red.How to replace the fuseOpen the fuse compartment witha screwdriver and replace the fuseand fuse cover.1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) Automatic Gain Control (AGC) +15 dBand Automatic Tracing White Balance(ATW)(3) Camera synchronization mode selec-table between internal (INT), Line-locked(LL) and Multiplexed Vertical Drive (VD2)for WV-CP230 and WV-CP234.FEATURES2. Minimum illumination of 0.6 lx (0.06 foot-can-dle) at F0.75 (equivalent to 2.0 lx (0.2 foot-candle) at F1.4)3. Signal-to-noise ratio of 50 dB4. Horizontal resolution of 480 lines5. Auto iris lens control selectable betweenvideo signal and DC power supply.1. Do not attempt to disassemble the camera.To prevent electric shock, do not removescrews or covers.There are no user serviceable parts inside.Ask a qualified service person for servicing.2. Handle the camera with care.Do not abuse the camera. Avoid striking,shaking, etc. The camera could be damagedby improper handling or storage.3. Do not expose the camera to rain ormoisture, or try to operate it in wet areas.Turn the power off immediately and ask aqualified service person for servicing.Moisture can damage the camera and alsocreate the danger of electric shock.4. Do not use strong or abrasive detergentswhen cleaning the camera body.Use a dry cloth to clean the camera whendirty.In case the dirt is hard to remove, use a milddetergent and wipe gently.5. Clean the CCD faceplate with care.Do not clean the CCD with strong or abrasivedetergents. Use lens tissue or a cotton tippedapplicator and ethanol.6. Never face the camera towards the sun.Do not aim the camera at bright objects.Whether the camera is in use or not, neveraim it at the sun or other extremely brightobjects. Otherwise, blooming or smear maybe caused.7. Do not operate the camera beyond thespecified temperature, humidity or powersource ratings.Use the camera under conditions where tem-perature is between –10°C - +50°C (14°F -122°F), and humidity is below 90 %. Theinput power source is 220 - 240 V AC 50 Hzfor WV-CP230, 12 V DC for WV-CP232, and24 V AC 50 Hz for WV-CP234.PRECAUTIONSColour CCTV CamerasWV-CP230/WV-CP232/WV-CP234Before attempting to connect or operate this product,please read these instructions completely.CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER (ORBACK), NO USER SERVICEABLE PARTSINSIDE.REFER SERVICING TO QUALIFIED SERVICEPERSONNEL.The exclamation point within anequilateral triangle is intended toalert the user to the presence ofimportant operating and mainte-nance (servicing) instructions in theliterature accompanying the appli-ance.The lightning flash with arrowheadsymbol, within an equilateral trian-gle, is interned to alert the user tothe presence of uninsulated "dan-gerous voltage" within the product'senclosure that may be of sufficientmagnitude to constitute a risk ofelectric shock to persons.WARNING:TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TORAIN OR MOISTURE.The serial number of this product may be found onthe top of the unit.You should note the serial number of this unit in thespace provided and retain this instruction as a per-manent record of your purchase to aid identificationin the event of theft.Model No.Serial No.Caution:Connect to 12 V DC (10.5 V-16 V) or 24 VAC (19.5 V-28 V) class 2 power supply only.Make sure to connect the grounding lead tothe GND terminal when the power is sup-plied from a 24 V AC power source.VIDEO OUTGNDAC 24V IN1 2VIDEO OUT

LL INTELC ALCSOFT SHARPOFF BLC ONDC VIDEOLL INTELC ALCSOFT SHARPOFF BLC ONDC VIDEOWV– CP230VIDEO OUTELC ALCSOFT SHARP0FF BLC ONDC VIDEODC 12V INMAJOR OPERATING CONTROLS AND THEIR FUNCTIONSq Auto Iris Lens ConnectorSupplies power and control signals to an autoiris lens (not supplied).w Flange-back Adjusting RingThis ring adjusts the back-focal distance orpicture focus. Rotate this ring clockwise for aC-mount lens or counterclockwise for a CS-mount lens.e Lens (option)r Camera Mounting Screw HoleThis hole is for mounting the camera onto amounting bracket. The camera is originallydesigned to be mounted from the bottom, buta top-mounting type is also available. Tomount from the top, remove the mountadapter from the bottom of the camera byremoving two fixing screws. Attach the mountadapter to the top as shown in the diagram,then mount the camera on the mountingbracket. Make sure that two original screwsare used when mounting the mount adapter;longer type screws may damage inner com-ponents.t Power Cord (only WV-CP230)Connect this power cord to an electrical out-let of 220 - 240 V AC 50 Hz.y DC 12 V Input Terminal(DC 12 V IN (only WV-CP232))This terminal is for connecting the 12 V DCpower supply cord.u AC 24 V Input Terminal(AC 24 V IN (only WV-CP234))This terminal is for connecting the 24 V AC50 Hz power supply cord.i Synchronization Mode Selector(INT, LL (only WV-CP230 and WV-CP234))Selects the camera synchronization modefrom internal sync mode (INT) or line-lockmode (LL).INT: Sets to internal 2:1 interlace.LL: Sets to Line-lock mode.o Automatic Light Control/Electronic LightControl Selector (ALC , ELC)Lets you select the mode according to thelens type that is used with this camera.ALC: Select this mode when an auto iris lens(ALC lens) is used with this camera.ELC: Select this mode when a fixed iris lensor manual iris lens is used with this cam-era.!0 Detail/Aperture Level Selector(SOFT/SHARP)The detail/aperture level can be selected withthis selector. Set it to the desired positionwhile observing the picture on the monitor.SHARP: Normal position.SOFT: Select this position when a QuadSystem is connected to this camera.!1 Back Light Compensation Mode Selector(BLC ON, OFF)Lets you select the mode according to theposition of the object and light conditions onthe screen.ON: Select this mode when a strong lightsuch as a spotlight is in the background.OFF: Normal picture.!2 Lens Drive Signal Selector (VIDEO, DC)Lets you select the mode according to thetype of auto iris lens drive signal to be sup-plied to the lens from the auto iris lens con-nector.VIDEO: Select this mode if you are using aauto iris lens that requires a video drivesignal.DC: Select this mode if you are using a autoiris lens that requires a DC drive signal.!3 Video Output Connector (VIDEO OUT)This connector is for connecting with theVIDEO IN connector of the video monitor.Whenever the multiplexed vertical drive (VD2)signal is supplied to this connector, the cam-era synchronization mode is automatically setto Vertical Drive.N1098-0 YWV8QA5084AN Printed in JapanN 30Wij verklaren als enige aansprakelijke, dat het product waaropdeze verklaring betrekking heeft, voldoet aan de volgende nor-men of andere normatiefve dokumenten, overeenkomstig debepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.Vi erklærer os eneansvarlige for, at dette produkt, som dennedeklaration omhandler, er i overensstemmelse med denfølgende standarder eller andre normative dokumenter i følgebestemmelserne i direktivene 73/23/EEC og 89/336/EEC.Vi deklarerar härmed värt fulla ansvar för att den produkt tillvilken denna deklaration hänvisar är i överensstämmelse medstandarddokument, eller andra normativa dokument somframstölls i Direktiv 73/23/EEC och 89/336/EEC.Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämäilmoitus koskee, noudattaa seuraavia standardeja tai muitaohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EECia 89/336/EEC. säädöksiä.Vi erklærer oss alene ansvarlige for at produktet som denneerklæringen gjelder for, er i overensstemmelse med følgendenormer eller andre normgivende dokumenter som fælgerbestemmelsene i direktiven 73/23/EEC og 89/336/EEC.We declare under our sole responsibility that the product towhich this declaration relates is in conformity with the stan-dards or other normative documents following the provisions ofDirectives EEC/73/23 and EEC/89/336.Noi dichiariamo sotto nostra esclusiva responsabilità che ilprodotto a cui si riferisce la presente dichiarazione risulta con-forme ai seguenti standard o altri documenti normativi confor-mi alle disposizioni delle direttive CEE/73/23 e CEE/89/336.For U.K.

/ 4

Related manuals for Panasonic WVCP230 - CCD 120V