SUPER-D3 ON: Enables SUPER-D3 to compensate backlight automatically.SUPER-D3 OFF: Enables manual setting to compensate backlight.Notes:• When set to ON, the available parameters for SHUTTER and SENS-UP will be limitedas shown on the next page.• Set SUPER-D3 to OFF when noise in a bright portion, flickerings, or color deteriorationare observed.1. Select ALC for ALC/ELC on the CAM SETUP menuand press SET.→ The ALC CONT menu opens.2. Select ON for SUPER-D3.3. Adjust the video output level (LEVEL) by moving the"I" cursor. It may be better to adjust LEVEL slightlyhigher.First, select a language for menu display and camera ID display.Language Setup (LANGUAGE SETUP)1. Select LANGUAGE on the top menu and press SET.→ The LANGUAGE SETUP menu opens.2. Select a language. The default setting is English.Available languages: ENGLISH, FRANÇAIS,DEUTSCH, ESPAÑOL, ITALIANO, êìëëäàâ,JAPANESE, CHINESE3. Select SET on the menu and press the SET button.1. Camera Identification Setting (CAMERA ID)Assign a name to the camera using up to 16 charactersto display it overlaying on the camera picture in theselected position.Note: If you change the language selection after theassignment of camera ID, it will be erased.1. On the CAMERA SETUP menu, select ON↓ or OFF↓for CAMERA ID and press SET.ON↓: Displays entered camera ID.OFF↓: Does not display the ID.→The CAMERA ID menu opens.2. Select a character from the character areaand press SET.→The selected characters are displayedin the editing area.3. Repeat these procedures until all charac-ters are entered.• To enter a blank space, select SPACE andpress SET.• To replace a specific character in the edit-ing area:1. Move the cursor to the editing areaand then move the pointer to the char-acter to be replaced pressing the Land R buttons.2. Move the cursor to a candidate char-acter in the character area and pressSET.• To erase all characters of the camera ID,select RESET and press SET.Note: For Chinese language, up to 8 char-acters can be entered.4 To specify the ID display position:1. Select POSI and press SET.→ The entered camera ID will be highlighted on the screen.2. Move it into the appropriate position and press SET.→ The position is determined and the screen will return to the CAMERA ID menu.Note: Keep pressing any of L/R/U/D for a second or more to move the camera IDfaster as necessary.2. Light Control Mode Setting (ALC/ELC)Select a light control mode depending on the lens type mounted. The default setting is ALC.ALC↓: Is applicable to the auto iris lens. SUPER-D3 is available with this selection.ELC↓: Is applicable to the fixed or manual iris lens.Cautions:1. Under bright lighting conditions such as outdoors, use an ALC lens because the ELCcontrol range is not wide enough under these conditions.2. Use an ALC type lens if the following phenomena occur:• Strong smear and/or blooming on highlighted objects such as a spotlight or sunlightfrom windows.• Noticeable flicker in the picture and/or color rendition variations.3. If ELC is selected, SUPER-D3 and SHUTTER are not available and the white balancemode is automatically set to ATW1 or ATW2 previously set.4. If ELC is selected and a fixed iris lens is used, the focal depth becomes shallowerthan with the use of an ALC lens. Therefore, the range of focus-to-object distancebecomes narrower.2-1. ALC Mode with SUPER-D3 ONSuper Dynamic 3 Function (SUPER-D3)In the SUPER-D3 mode, more photometric weight is given to the center of the screen than tothe edge where a bright backlight would most likely be located.**CAMERA SETUP** 1/2CAMERA ID OFFALC/ELC ALCSHUTTER OFFAGC ON(HIGH)SENS UP OFFSYNC INTWHITE BAL ATW1MOTION DET OFFDNR HIGHRESOLUTION HIGHBW MODE↵↵↵↵(To be continued reverse page)SETTING PROCEDURES**ALC CONT**BACK LIGHT COMPSUPER-D3 ONLEVEL ..I......- +RET TOP ENDWV-CP480 HighlightedCAMERA ID0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ().,'":;!?=+-*/%$SPACE POSIRET TOP END RESET................CharacterCursorPointerCharacterAreaCommandEditingAreaNighttimeNighttime DaytimeDaytimeSUPER-D3 ON SUPER-D3 OFF**LANGUAGE SETUP**LANGUAGE ENGLISHSETRET TOP END