Panasonic WV-SFV311 Installation Manual

Also see for WV-SFV310: Operating instructions Important information Operating instructions

Panasonic WV-SFV311 Installation Manual Manual pdf 1 page image

● The MONITOR OUT terminal output can be switched for NTSC or PAL monitors.Installation GuideNetwork CameraModel No. WV-SFV311/WV-SFV310(This illustration represents WV-SFV311.)PGQX1558XA sL0514-2064 Printed in China● This manual describes the installation procedures, network camera installation, cable connec-tions, and the angle of view adjustment.● Before reading this manual, be sure to read the Important Information.● This manual describes how to install the network camera using the WV-SFV311 model as anexample.Major operating controlsThe component names of the camera are as follows. Refer to the illustration when installing oradjusting the camera.Standard accessories Making connectionsImportant Information ............................... 1 pc.Installation Guide (this document) ............ 1 setWarranty card ........................................... 1 setCD-ROM *1 ................................................. 1 pc.Code label *2 .............................................. 1 pc.*1 The CD-ROM contains the operating instructions and different kinds of tool software pro-grams.*2 This label may be required for network management. The network administrator shall retainthe code label.The following parts are used during installation procedures.Ⓐ Base bracket........................................ 1 pc.Ⓒ Fixing screws for attachment plate(M4 x 8 mm) ...................................... 5 pcs.(of them, 1 for spare)Ⓖ Template B (for the base bracket) .. 1 sheet.Ⓘ 2P power cable .................................... 1 pc.Ⓚ Waterproof tape ................................... 1 pc.Ⓑ Attachment plate .................................. 1 pc.Ⓓ 4P alarm cable..................................... 1 pc.Ⓔ MONITOR OUT conversion plug ......... 1 pc.Ⓕ Template A (for the attachment plate) 1 sheet.Ⓗ Bit ........................................................ 1 pc.Ⓙ LAN cable cover .................................. 1 pc.Ⓗ Ⓚ● How to initialize the cameraFollow the steps below to initialize the network camera.q Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the cam-era. When using an external power supply, disconnect the 2P power cable plug from the camera.w Turn on the power of the camera while holding down the INITIAL SET button, and then keepholding down the button for 5 seconds or more. About 2 minutes later, The camera will startup and the settings including the network settings will be initialized.● When data is being sent via the network camera Blinks green (accessing)Turn off each system’s power supply before making a connection. Before making connections,prepare the required peripheral devices and cables.● When the camera is able to communicate with the connected device Lights orange● When an SD memory card* 1 is inserted and could Lights off → Blinks green →be recognized Lights off● When data can be saved after the SD memory card is Lights off → Lights greeninserted and the SD ON/OFF button is pressed● When data can be saved to the SD memory card Lights green● When the SD memory card is removed after holding down Lights green → Blinks green → Lights offthe SD ON/OFF button for about 2 seconds● When data cannot be saved to the SD memory card because Lights offan abnormality was detected or the SD memory card isconfigured not to be used● When AF (Auto Focus) operation is being Blinks red (Interval of 1 time/ second)executed SFV311● When the focus assist function is activated SFV310 Blinks red (1 time)● When the focus ring is positioned near the best Lights redfocus position SFV310● When the set is being started Lights red● When an SD memory card is recognized normally Lights red → Lights off● When an abnormality is detected in SD card or the SD Lights redslot is not used after the camera has startedIMPORTANT:● When the camera is initialized, the settings including the network settings will be initial-ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will notbe initialized.● Before initializing the settings, it is recommended to write down the settings in advance.● Do not turn off the power of the camera during the process of initialization. Otherwise, itmay fail to initialize and may cause malfunction.IMPORTANT:● This is valid if the [Monitor out] is set to [Switch priority] ([Switch priority] is selected bydefault). For details, refer to the Operating Instructions (included in the CD-ROM).IMPORTANT:● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight, STP: For Europe).● The maximum cable length is 100 m {328 feet}.● Make sure that the PoE device in use is compliant with IEEE802.3af standard.● When connecting both the 12 V DC power supply and the PoE device for power sup-ply, 12 V DC will be used for power supply*.* If a 12 V DC power supply and a PoE hub or router are used at the same time, net-work connections may not be possible. In this case, disable the PoE settings.Refer to the operating instructions of the PoE hub or router in use.* In the situation where a 12 V DC power supply and a PoE hub or router are used at thesame time and the 12 V DC power supply is then disconnected, the power supply maybe stopped and the camera may restart depending on the PoE hub or router used.● When the LAN cable is disconnected once, reconnect the cable after around 2 seconds.When the cable is quickly reconnected, the power may not be supplied from the PoE device.● When cables are used outdoors, there is a chance that they may be affected by lightning.In this case, install a lightning arrester just before where the cables connect to the camera.Connect a LAN cable (category 5 or better, straight, STP: For Europe)Waterproof treatment for the cable joint sectionsWhen connecting to a network using a PoE hubMicrophone/line input cable SFV311Connect a monaural mini plug (ø3.5 mm).● Input impedance: Approx. 2 kΩ (unbalanced)● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)Less than 10 m {32.8 feet} (for line input)● Recommended microphone: Plug-in power type (option)● Supply voltage: 2.5 V ±0.5 V● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)● Input level for the line input: Approx. –10 dBVIMPORTANT:● Be sure to use the 4P alarm cable provided with this product.● Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur-ing the setting. Refer to the Operating Instructions on the provided CD-ROM for fur-ther information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”,“Alarm input”, “Alarm output” or “AUX output”).● When using the EXT I/O terminals as the output terminals, ensure they do not causesignal collision with external signals.● Install external devices so that they do not exceed the ratings above.Connect the alarm input/output cable• ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)OFF: Open or 4 V - 5 V DCON: Make contact with GND (required drive current: 1 mA or more)• ALARM OUT, AUX OUTOutput specification: Open collector output (maximum applied voltage: 20 V DC)Open: 4 V - 5 V DC by internal pull-upClose: Output voltage 1 V DC or less (maximum drive current: 50 mA)* The default of EXT I/O terminals is “Off”.Connect an external amplifier-embedded speaker to the audio output cable SFV311Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.).*● Output impedance: Approx. 600 Ω (unbalanced)● Recommended cable length: Less than 10 m {32.8 feet}● Output level: –20 dBVIMPORTANT:● Connect/disconnect the audio cables and turn on the power of the camera after turn-ing off the power of the audio output devices. Otherwise, loud noise may be heardfrom the speaker.● Make sure that the stereo mini plug is connected to this cable. When a monaural miniplug is connected, audio may not be heard.When connecting a monaural speaker with amplifier, use a locally procured conver-sion cable (mono-stereo).Adequate waterproof treatment is required for the cables when installing the camera with cablesexposed or installing it under the eaves. The camera body is waterproof, but the cable ends arenot waterproof.Be sure to use the supplied waterproof tape at the points where the cables are connected to ap-ply waterproof treatment in the following procedure. Failure to observe this or use of a tape otherthan the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting inmalfunction. Before starting the installation, check the entire system configuration. The following illustrationgives a wiring example of how to connect the camera to the network via a PoE device (hub). < Alarm input/output cable, power cable, micro-phone/line input cable SFV311 , audio output cableSFV311 >IMPORTANT:How to wind the supplied waterproof tape● Also waterproof the 2P power cable (accessory), 4Palarm cable (accessory), and external connections inthe same way.● Stretch the tape by approx. twice (see the illustration)and wind it around the cable. Insufficient tape stretchcauses insufficient waterproofing.● To prevent the LAN cable hook from coming looseeasily, fit the Ⓙ LAN cable cover onto the pigtailcable as illustrated, and then slide it in the directionindicated by the arrow.The connector of the LAN cable used with this cam-era must meet the following restrictions.Height when inserted (From bottom to hook.):Max. 16 mm {5/8 inches}Connector width: Max. 14 mm {9/16 inches}● To install this product outdoors, be sure to waterproofthe cables. Waterproof grade (IEC IP66 or equiva-lent) is applied to this product only when it is installedcorrectly as described in these operating instructionsand appropriate waterproof treatment is applied. Theinternal parts of base brackets are not waterproofed.2xIMPORTANT:● The adjustment monitor is used for checking the adjustment of the angular field of viewwhen installing the camera or when servicing. It is not provided for recording/monitoring use.● Depending on the monitor, some characters (camera title, preset ID, etc.) may not bedisplayed on the screen.● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.● If a PoE hub is not used, each network camera must be connected to a 12 V DCpower supply.● When using 12 V DC, power supply from a PoE hub or router is not required.INITIAL SET buttonDehumidifyingdeviceAuto focus (AF) button SFV311Focus Assist (F.A.) button SFV310• FRONT must posi-tioned in front of thecamera (on thePanasonic logo side).Direction markerfor installation(FRONT )Data Matrix: To ourwebsite* 2Direction marker for installation ( TOP)Dome coverAzimuth adjustment ringTilting tablePanning tableCamera fixing screwThe hook engageswith the connectorterminalⒿ LAN cable coverⒸ Fixing screws forattachment plate(accessory)Wind the tape in ahalf-overlappingmanner.Wind the tape in ahalf-overlapping manner.Enclosure(Screw size 6.35 mm{1/4 inches} torx wrench)CameraInner domeⒷ Attachmentplate (accessory)Ⓐ Base bracket(accessory)ACT indicatorLINK indicatorSD MOUNT indicatorSD ERROR/AF indicator SFV311 F.A. indicator SFV310*1 SDXC/SDHC/SD memory card is described as SD memory card.*2 Depending on the scanning application used, the Data Matrix may not be able to beread correctly. In this case, access the site by directly entering the following URL.http://security.panasonic.com/pss/security/support/qr_sp_select.htmlMONITOR OUT terminal(factory shipment: NTSCmonitor)Connect the output cable of the AC adaptor to the 2P power cable.Power cable12 V DCRed PositiveBlack NegativeLAN cable (category 5 or better, straight, STP: For Europe)Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.* Recommended cable length from the speaker: less than 10 m {32.8 feet}Recommended cable length from the microphone: less than 1 m {3.28 feet}For U.S. and Canada:Panasonic System CommunicationsCompany of North America,Unit of Panasonic Corporationof North Americawww.panasonic.com/business/For customer support, call 1.800.528.6747Two Riverfront Plaza, Newark, NJ 07102-5490Panasonic Canada Inc.5770 Ambler Drive, Mississauga,Ontario, L4W 2T3 Canada(905)624-5010www.panasonic.caFor Europe and other countries:Panasonic Corporationhttp://panasonic.netPanasonic System Networks Co., Ltd.Fukuoka, JapanAuthorised Representative in EU:Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg, Germany* Use an external poweredspeaker.Connect the power cableIMPORTANT:● The 12 V DC power supply shall be insulated from the commercial AC power.● Be sure to use the 2P power cable provided with this product.● Be sure to fully insert the 2P power cable into the 12 V DC power supply terminal.Otherwise, it may damage the camera or cause malfunction.● When installing the camera, make sure that excessive force is not applied to thepower cable.Caution:● A READILY ACCESSIBLE DISCONNECT DEVICE SHALLBE INCORPORATED TO THE EQUIPMENT POWEREDBY 12 V DC POWER SUPPLY.● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).Included Installation Instructions© Panasonic System Networks Co., Ltd. 2014Screen displaytop (TOP )NTSC/PAL switchⒹ 4P alarm cable (accessory)GND (black)ALARM IN3, AUX OUT (gray) (Terminal 3)ALARM IN2, ALARM OUT (red) (Terminal 2)ALARM IN1, DAY/NIGHT IN (green) (Terminal 1)Stretch the tape toabout twice.Powered speaker Adjustment monitorPCPoE device (hub)LAN cable(category 5 or better,straight, STP: For Europe)LAN cable(category 5 orbetter, straight,STP: For Europe)LAN cable(category 5 or better,straight, STP: For Europe)Adjustment monitorRecommended totalextended cable length*Powered speakerMicrophoneMicrophoneⒾ 2P power cable (accessory)RJ-45 (female)Network cableAlarm input/output cableMicrophone/line input cable (white) SFV311Audio output cable (black) SFV311LAN cable (category 5 or betterstraight, STP: For Europe)4P alarm cable(accessory)Power cable(12 V DC)12 V DC (red)GND (black)SD slotSD ON/OFF button● Points up when installing to a wall.

/ 2

Related manuals for Panasonic WV-SFV310