Panasonic WV-SFV631L Installation Manual
Also see for WV-SFV611L: Operating instructionsImportant informationOperating instructionsImportant informationSpecifications
● The MONITOR OUT terminal output can be switched for NTSC or PAL monitors.Installation GuideNetwork CameraModel No. WV-SFV631L/WV-SFV631LTWV-SFV611LWV-SFV631L(This illustration represents WV-SFV631L.)PGQX1455XA avs1213-2064 Printed in China● This manual describes the installation procedures, network camera installation, cable connec-tions, and the angle of view adjustment.● Before reading this manual, be sure to read the Important Information.● This manual describes how to install the network camera using the WV-SFV631L model as anexample.Major operating controlsThe component names of the camera are as follows. Refer to the illustration when installing oradjusting the camera.Standard accessories Making connectionsImportant Information ............................... 1 pc.Installation Guide (this document) ............ 1 setWarranty card ........................................... 1 setCD-ROM *1 ................................................. 1 pc.Code label *2 .............................................. 1 pc.*1 The CD-ROM contains the operating instructions and different kinds of tool software pro-grams.*2 This label may be required for network management. The network administrator shall retainthe code label.The following parts are used during installation procedures.A Base bracket........................................ 1 pc.C Fixing screws for attachment plate(M4 x 8 mm) ...................................... 5 pcs.(of them, 1 for spare)G Template B (for the base bracket) .. 1 sheet.I 2P power cable .................................... 1 pc.K Waterproof tape ................................... 1 pc.B Attachment plate .................................. 1 pc.D 4P alarm cable..................................... 1 pc.E MONITOR OUT conversion plug ......... 1 pc.F Template A (for the attachment plate) 1 sheet.H Bit ........................................................ 1 pc.J LAN cable cover .................................. 1 pc.H K● How to initialize the cameraFollow the steps below to initialize the network camera.1 Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the cam-era. When using an external power supply, disconnect the 2P power cable plug from the camera.2 Turn on the power of the camera while holding down the INITIAL SET button, and then keepholding down the button for 5 seconds or more. About 2 minutes later, The camera will startup and the settings including the network settings will be initialized.When data is being sent via the network camera Blinks green (accessing)●Turn off each system’s power supply before making a connection. Before making connections,prepare the required peripheral devices and cables.When the camera is able to communicate with the connected device● Lights orangeWhen an SD memory card*● 1 is inserted and could Lights off → Blinks green →be recognized Lights offWhen data can be saved after the SD memory card is Lights off → Lights green●inserted and the SD ON/OFF button is pressedWhen data can be saved to the SD memory card Lights green●When the SD memory card is removed after holding down● Lights green → Blinks green → Lights offthe SD ON/OFF button for about 2 secondsWhen data cannot be saved to the SD memory card because● Lights offan abnormality was detected or the SD memory card isconfigured not to be usedWhen AF (Auto Focus) operation is being executed● Blinks red (Interval of 1 time/ second)When the set is being started Lights red●When an SD memory card is recognized normally Lights red → Lights off●When an abnormality is detected in both SD1 and SD2● Lights redcards after the camera has startedWhen an abnormality is only detected in the SD1 card Lights red → Blinks red●after the camera has started (Interval of 1 time/ 3 seconds)When an abnormality is only detected in the SD2 card Lights red → Blinks red●after the camera has started (Interval of 2 times/ 3 seconds)IMPORTANT:When the camera is initialized, the settings including the network settings will be initial-●ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will notbe initialized.Before initializing the settings, it is recommended to write down the settings in advance.●Do not turn off the power of the camera during the process of initialization. Otherwise, it●may fail to initialize and may cause malfunction.IMPORTANT:This is valid if the [Monitor out] is set to [Switch priority] ([Switch priority] is selected by●default). For details, refer to the Operating Instructions (included in the CD-ROM).IMPORTANT:Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight).●The maximum cable length is 100 m {328 feet}.●Make sure that the PoE device in use is compliant with IEEE802.3af standard.●When connecting both the 12 V DC power supply and the PoE device for power sup-●ply, 12 V DC will be used for power supply*.* If a 12 V DC power supply and a PoE hub or router are used at the same time, net-work connections may not be possible. In this case, disable the PoE settings.Refer to the operating instructions of the PoE hub or router in use.* In the situation where a 12 V DC power supply and a PoE hub or router are used at thesame time and the 12 V DC power supply is then disconnected, the power supply maybe stopped and the camera may restart depending on the PoE hub or router used.When the LAN cable is disconnected once, reconnect the cable after around 2 seconds.●When the cable is quickly reconnected, the power may not be supplied from the PoE device.When cables are used outdoors, there is a chance that they may be affected by lightning.●In this case, install a lightning arrester just before where the cables connect to the camera.Connect a LAN cable (category 5 or better, straight)Waterproof treatment for the cable joint sectionsWhen connecting to a network using a PoE hubMicrophone/line input cableConnect a monaural mini plug (ø3.5 mm).Input impedance: Approx. 2 kΩ (unbalanced)●Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)●Less than 10 m {32.8 feet} (for line input)Recommended microphone: Plug-in power type (option)●Supply voltage: 2.5 V ±0.5 V●Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)●Input level for the line input: Approx. –10 dBV●IMPORTANT:Be sure to use the 4P alarm cable provided with this product.●Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur-●ing the setting. Refer to the Operating Instructions on the provided CD-ROM for fur-ther information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”,“Alarm input”, “Alarm output” or “AUX output”).When using the EXT I/O terminals as the output terminals, ensure they do not cause●signal collision with external signals.Install external devices so that they do not exceed the ratings above.●Connect the alarm input/output cable |
Related manuals for Panasonic WV-SFV611L
Panasonic WV-SFR631L Installation Manual
Panasonic WV-SFV311 Installation Manual
Panasonic WV-SFV531 Installation Manual
Panasonic WV-SFV110 Installation Manual
Panasonic WV-SFV481 Installation Manual
Panasonic WV-SFV531 Installation Manual
Panasonic WV-SF438 Installation Manual
Panasonic WV-SF448 Installation Manual
Panasonic WV-SF135 Installation Manual
Panasonic WV-SF138 Installation Manual
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine