Parker P1D-S Installation Instructions Manual

149127007796-P1D-S AnnexeP1D-S Declaration of ConformityAccording to ATEX 94/9/ECP1D-S Declaration of IncorporationAccording to EC Machinery Directive 2006/42/ECWe Parker Hannifin ManufacturingGermany GmbH & Co. KGPneumatic Division EuropeIndustriestrasse 870794 Filderstadt GermanyDeclare that the following pneumatic cylinders have been assessed in accordance with ATEX 94/9/EC (Products foruse in potentially explosive atmospheres). ISO15552 Cylinders P1D-S***MS-**** range are compatible for the use inexplosive atmosphere Ex II 2 GD c T4 (T120°C).P1D-S is designed for utilization in applications falling under the scope of the ATEX 94/9/EC. This product is designedand manufactured in compliance with following elements: EN 1127-1:2007 Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts andmethodology EN 13463-1:2009 Non electrical equipment for use in potentially explosive atmospheres – Part 1: Basic methodand requirements EN 13463-5 Non-electrical equipment intended for use in potentially explosive atmospheres – Part 5: Protectionby constructional safety ´c´ EN 983+A1:2008 Safety of machinery – Safety requirements for fluid power systems and their components -PneumaticsAs manufacturer of the partly completed machine we declare that: The specified cylinders correspond to the listed essential requirements of the EC Machinery Directive2006/42/EC The relevant technical documentation is complied in accordance with part B of Annex VII The relevant technical documentation in accordance with part B of Annex VII will be transmitted in response toa reasonable request by the national authoritiesProduct: Pneumatic Air motor P1D-S seriesDirectives Date Applied and fulfilled essentialrequirements2006/42/EC 2006-06 1.1.2, 1.1.5, 1.3.4, 1.5.3, 1.7.3, 1.7.4Standards Date RemarkDIN EN ISO 12100 2011-03 Partly fulfilledThis partly completed machinery must not be put into service until the final machinery into which it is to beincorporates has been declared in conformity with the provisions of the Directive 2006/42/EG, were appropriated.P1D-S032MS-****, all strokesP1D-S040MS-****, all strokesP1D-S050MS-****, all strokesP1D-S063MS-****, all strokesP1D-S080MS-****, all strokesP1D-S100MS-****, all strokesP1D-S125MS-****, all strokesFilderstadt, Germany October 2014_________________________Ing. Franck RoussillonEuropean Product ManagerActuators Business Unit, Pneumatic Division EuropeAdditional InformationThis coverage could only be referred to aslong as operations needed for finalassembling and starting up of thesesproducts comply with standards relating tothe above mentioned directive. Each timethis will be required for compliance purpose,the user will have to apply for a completecoverage of the final assembled systemaccording to the above mentioned directiveand relating standards9127007796-P1D-S AnnexeP1D-S Declaration of ConformityAccording to ATEX 94/9/ECP1D-S Declaration of IncorporationAccording to EC Machinery Directive 2006/42/ECWe Parker Hannifin ManufacturingGermany GmbH & Co. KGPneumatic Division EuropeIndustriestrasse 870794 Filderstadt GermanyDeclare that the following pneumatic cylinders have been assessed in accordance with ATEX 94/9/EC (Products foruse in potentially explosive atmospheres). ISO15552 Cylinders P1D-S***MS-**** range are compatible for the use inexplosive atmosphere Ex II 2 GD c T4 (T120°C).P1D-S is designed for utilization in applications falling under the scope of the ATEX 94/9/EC. This product is designedand manufactured in compliance with following elements: EN 1127-1:2007 Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts andmethodology EN 13463-1:2009 Non electrical equipment for use in potentially explosive atmospheres – Part 1: Basic methodand requirements EN 13463-5 Non-electrical equipment intended for use in potentially explosive atmospheres – Part 5: Protectionby constructional safety ´c´ EN 983+A1:2008 Safety of machinery – Safety requirements for fluid power systems and their components -PneumaticsAs manufacturer of the partly completed machine we declare that: The specified cylinders correspond to the listed essential requirements of the EC Machinery Directive2006/42/EC The relevant technical documentation is complied in accordance with part B of Annex VII The relevant technical documentation in accordance with part B of Annex VII will be transmitted in response toa reasonable request by the national authoritiesProduct: Pneumatic Air motor P1D-S seriesDirectives Date Applied and fulfilled essentialrequirements2006/42/EC 2006-06 1.1.2, 1.1.5, 1.3.4, 1.5.3, 1.7.3, 1.7.4Standards Date RemarkDIN EN ISO 12100 2011-03 Partly fulfilledThis partly completed machinery must not be put into service until the final machinery into which it is to beincorporates has been declared in conformity with the provisions of the Directive 2006/42/EG, were appropriated.P1D-S032MS-****, all strokesP1D-S040MS-****, all strokesP1D-S050MS-****, all strokesP1D-S063MS-****, all strokesP1D-S080MS-****, all strokesP1D-S100MS-****, all strokesP1D-S125MS-****, all strokesFilderstadt, Germany October 2014_________________________Ing. Franck RoussillonEuropean Product ManagerActuators Business Unit, Pneumatic Division EuropeAdditional InformationThis coverage could only be referred to aslong as operations needed for finalassembling and starting up of thesesproducts comply with standards relating tothe above mentioned directive. Each timethis will be required for compliance purpose,the user will have to apply for a completecoverage of the final assembled systemaccording to the above mentioned directiveand relating standards9127007796-P1D-S AnnexeP1D-S Declaration of ConformityAccording to ATEX 94/9/ECP1D-S Declaration of IncorporationAccording to EC Machinery Directive 2006/42/ECWe Parker Hannifin ManufacturingGermany GmbH & Co. KGPneumatic Division EuropeIndustriestrasse 870794 Filderstadt GermanyDeclare that the following pneumatic cylinders have been assessed in accordance with ATEX 94/9/EC (Products foruse in potentially explosive atmospheres). ISO15552 Cylinders P1D-S***MS-**** range are compatible for the use inexplosive atmosphere Ex II 2 GD c T4 (T120°C).P1D-S is designed for utilization in applications falling under the scope of the ATEX 94/9/EC. This product is designedand manufactured in compliance with following elements: EN 1127-1:2007 Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts andmethodology EN 13463-1:2009 Non electrical equipment for use in potentially explosive atmospheres – Part 1: Basic methodand requirements EN 13463-5 Non-electrical equipment intended for use in potentially explosive atmospheres – Part 5: Protectionby constructional safety ´c´ EN 983+A1:2008 Safety of machinery – Safety requirements for fluid power systems and their components -PneumaticsAs manufacturer of the partly completed machine we declare that: The specified cylinders correspond to the listed essential requirements of the EC Machinery Directive2006/42/EC The relevant technical documentation is complied in accordance with part B of Annex VII The relevant technical documentation in accordance with part B of Annex VII will be transmitted in response toa reasonable request by the national authoritiesProduct: Pneumatic Air motor P1D-S seriesDirectives Date Applied and fulfilled essentialrequirements2006/42/EC 2006-06 1.1.2, 1.1.5, 1.3.4, 1.5.3, 1.7.3, 1.7.4Standards Date RemarkDIN EN ISO 12100 2011-03 Partly fulfilledThis partly completed machinery must not be put into service until the final machinery into which it is to beincorporates has been declared in conformity with the provisions of the Directive 2006/42/EG, were appropriated.P1D-S032MS-****, all strokesP1D-S040MS-****, all strokesP1D-S050MS-****, all strokesP1D-S063MS-****, all strokesP1D-S080MS-****, all strokesP1D-S100MS-****, all strokesP1D-S125MS-****, all strokesFilderstadt, Germany October 2014_________________________Ing. Franck RoussillonEuropean Product ManagerActuators Business Unit, Pneumatic Division EuropeAdditional InformationThis coverage could only be referred to aslong as operations needed for finalassembling and starting up of thesesproducts comply with standards relating tothe above mentioned directive. Each timethis will be required for compliance purpose,the user will have to apply for a completecoverage of the final assembled systemaccording to the above mentioned directiveand relating standards9127007796-P1D-S AnnexeP1D-S Declaration of ConformityAccording to ATEX 94/9/ECP1D-S Declaration of IncorporationAccording to EC Machinery Directive 2006/42/ECWe Parker Hannifin ManufacturingGermany GmbH & Co. KGPneumatic Division EuropeIndustriestrasse 870794 Filderstadt GermanyDeclare that the following pneumatic cylinders have been assessed in accordance with ATEX 94/9/EC (Products foruse in potentially explosive atmospheres). ISO15552 Cylinders P1D-S***MS-**** range are compatible for the use inexplosive atmosphere Ex II 2 GD c T4 (T120°C).P1D-S is designed for utilization in applications falling under the scope of the ATEX 94/9/EC. This product is designedand manufactured in compliance with following elements: EN 1127-1:2007 Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts andmethodology EN 13463-1:2009 Non electrical equipment for use in potentially explosive atmospheres – Part 1: Basic methodand requirements EN 13463-5 Non-electrical equipment intended for use in potentially explosive atmospheres – Part 5: Protectionby constructional safety ´c´ EN 983+A1:2008 Safety of machinery – Safety requirements for fluid power systems and their components -PneumaticsAs manufacturer of the partly completed machine we declare that: The specified cylinders correspond to the listed essential requirements of the EC Machinery Directive2006/42/EC The relevant technical documentation is complied in accordance with part B of Annex VII The relevant technical documentation in accordance with part B of Annex VII will be transmitted in response toa reasonable request by the national authoritiesProduct: Pneumatic Air motor P1D-S seriesDirectives Date Applied and fulfilled essentialrequirements2006/42/EC 2006-06 1.1.2, 1.1.5, 1.3.4, 1.5.3, 1.7.3, 1.7.4Standards Date RemarkDIN EN ISO 12100 2011-03 Partly fulfilledThis partly completed machinery must not be put into service until the final machinery into which it is to beincorporates has been declared in conformity with the provisions of the Directive 2006/42/EG, were appropriated.P1D-S032MS-****, all strokesP1D-S040MS-****, all strokesP1D-S050MS-****, all strokesP1D-S063MS-****, all strokesP1D-S080MS-****, all strokesP1D-S100MS-****, all strokesP1D-S125MS-****, all strokesFilderstadt, Germany October 2014_________________________Ing. Franck RoussillonEuropean Product ManagerActuators Business Unit, Pneumatic Division EuropeAdditional InformationThis coverage could only be referred to aslong as operations needed for finalassembling and starting up of thesesproducts comply with standards relating tothe above mentioned directive. Each timethis will be required for compliance purpose,the user will have to apply for a completecoverage of the final assembled systemaccording to the above mentioned directiveand relating standards

/ 16

Related manuals for Parker P1D-S