45 501092 1 Dust Cover46 501972 2 Bolt47 501091 1 Air Plug48 501939 1 Belt Hook49 501938 2 Hex S.H.C.S.50 501998 1 Spring Pin51 501931 1 Spring Pin52 501089 1 Urethane Retainer53 501963 1 Steel Channel54 501966 1 Safety B55 501967 1 Safety Spring56 501968 1 E-Ring57 501969 1 Adjust Shaft58 501387 1 Spring59 501970 1 Safety A60 501971 1 No Mar Tip61 501951 1 Latch Cover62 501950 2 Spiral Pin63 501949 1 Front Latch Handle64 501948 1 Front Latch65 501947 1 Driver Guide Cover66 501946 1 Spiral Pin67 501940 2 Hex Soc.Hd.Bolt68 501941 1 Driver Guide Cover B69 501942 1 Driver Guide70 501943 1 Stopper Finger Spring71 501944 1 Stopper72 501945 1 Fixed Pin73 501953 1 Pusher Spring74 501954 1 Pusher75 501955 1 Spring Pin76 501952 1 Anchor Block77 501956 1 Negator Spring78 501960 1 Magazine Steel Cover79 501961 1 Counter Sunk Screw80 501959 1 Tap Bolt81 501958 1 Protecting Hood Cover82 501962 1 Lock Nut83 501957 1 Magazine A84 501973 1 Nameplate85 501302 1 Warning Label86 501140 1 Housing Label-left87 501141 1 Housing Label-right88 501995 1 Tap Bolt1 501885 1 T.H.S.C.S. 1/4-20 x 1/22 501896 1 Flat Washer3 501899 1 Deflector4 501901 1 Bolt5 501902 1 Cap6 501903 1 Seal7 501904 1 Spring, Main Valve*8 501905 2 O-Ring9 501906 1 Head Valve Piston10 501907 1 O-Ring11 501908 1 Collar12 501909 1 Packing13 501910 1 Piston Ring14 501911 1 O-Ring15 501912 1 Driver Blade16 501920 1 Cylinder Press Ring17 501913 1 O-Ring18 501914 1 Cylinder19 501915 1 Cylinder Ring20 501916 1 Cylinder Spacer21 501917 1 O-Ring22 501918 1 Bumper23 501919 1 Driver Guide24 501921 1 O-Ring25 501922 1 O-Ring26 501923 1 Plunger Cap27 501930 2 Spring Pin28 501924 1 Valve Plunger29 501925 2 O-Ring30 501926 1 O-Ring31 501927 1 Spring32 501928 1 Plunger33 500999 2 O-Ring34 501929 1 Trigger Valve Head35 501932 1 Spring36 501933 1 Trigger Unit37 501965 2 Tap Bolt38 501962 1 Lock Nut39 501964 1 Magazine B40 501961 1 Counter Sunk Screw41 501934 1 Trigger Pivot Pin42 501935 1 Housing43 501936 1 O-Ring44 501937 1 End CapPARTS LEGEND T250S-F16, 501680* Denotes Normal Wear Items.** Make sure Warning Label (501302) is properly affixed.Replace if necessary.Label available at no charge through the Service Parts Dept.DO NOT EXCEED MAXIMUMRECOMMENDED AIR PRESSURE600120600120Always wear hearing protection and eye protection devices,including side shields when operating or working in the vicinityof a tool.Operate the tool using only the recommended air pressure. Donot exceed the maximum air pressure marked on the tool. Besure the air pressure gauge is operating properly and check itat least twice a day.SAFETY INSTRUCTIONSWEAR EYE AND HEARING PROTECTION10Never use any bottled air or gases such asoxygen to operate the tool since they could causethe tool to explode.*************