Q CELLS Q.POWER-G5.1 Installation And Operation Manual

Contents

Q CELLS Q.POWER-G5.1 Installation And Operation Manual Manual pdf 6 page image

10 11INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.POWER-G5 / L-G5 • Q.PRIME-G5 / L-G5 – EN INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.POWER-G5 / L-G5 • Q.PRIME-G5 / L-G5 – EN2 PLANNING 2.3 Mounting optionsSpecificationsMODULE TYPE MOUNTING OPTION CLAMPING AREA1 [MM] TEST-LOAD ACC. IEC 61215PUSH/PULL [PA]Q.POWER L-G5.1Q.PRIME L-G5.1CL1 (4 point clamping onlong side)208-417 5400/2400CL1 (4 point clamping onlong side)0-625 2400/2400CL3 (4 point clamping onshort side)0-250 2400/2400FB1 (4 screws mountingon long module side)345 5400/2400IP1 (Slide-in / longmodule side)5400/2400IP1 (Slide-in / shortmodule side)2400/2400Q.POWER-G5.1Q.PRIME-G5.1CL1 (4 point clamping onlong side)246-493 5400/4000CL1 (4 point clamping onlong side)0-739 2400/2400CL3 (4 point clamping onshort side)0-248 2400/2400FB1 (4 screws mountingon long module side)332 5400/4000IP1 (Slide-in / longmodule side)5400/4000IP1 (Slide-in / shortmodule side)2400/24001 Distance between outer edge of module and middle of the clamp.DISTANCE BETWEEN MODULESÄ Maintain an interval of at least 10 mm between two modules along the short sideÄ Maintain an interval of at least 5 mm between two modules along the long sideMOUNTING OPTIONS CL1Ä Ensure, that the subconstruction does not run below the junction box.Ä Ensure, that the connection cables of the junction box don‘t run between laminate and substructure.MOUNTING OPTION FB1Ä Use M8 corrosion-proof screws and washers (min. diameter 16 mm).Ä Ensure, that the connection cables of the junction box don‘t run between laminate and substructure.• The fastening points are located on the backside of the module frame.Module SelectionFor detailed key electrical data, please refer to the actualdata sheet referring to the relevant Module (available atwww.q-cells.com).Ä Only connect modules of the same type and the samepower class.Safety FactorDuring normal operation, a module may generate a greatercurrent and / or higher voltage than that determined understandardized test conditions. Please use a safety factor of1.25 for the following:• Calculating the voltage measurement values (Voc) ofcomponents• Calculating the current measurement values (I SC) ofconductors• Sizing of control systems connected to the outlets ofthe solar modulesÄ Please follow the valid national guidelines for theinstallation of electrical systems.Series ConnectionConnection of modules in series is only permitted up tothe maximum system voltage as listed in the applicabledata sheet of all the relevant modules to be installed.Ä Take into account all possible operating situations and allrelevant technical norms and regulations when designingthe system. It has to be ensured that the maximumsystem voltage, including all necessary safety margins,is not exceeded.Ä Take the voltage limit of the inverter into account whendetermining the maximum number of modules in thestring.Parallel ConnectionModules may be damaged by the occurrence of reversecurrents (caused by module defects, ground leaks, ordefective insulation).Ä Ensure that the maximum reverse current load capacityindicated in the data sheet is met.In order to limit reverse currents that may occur, werecommend using the following safety options:1) Layout with a limited number of parallel connectedstrings :Without undertaking further current blocking measures,a maximum of two module strings may be operated inparallel on an inverter or MPP tracker.2) Layout with string fuses :place fuses for each string of modules at the plus andminus ends. Observe the maximum permitted numberof strings as indicated in the specifications provided bythe respective string fuse manufacturer and the technicalguidelines.NOTE!When installing different product versions, the lowestminimum permitted reverse current load capacity applies.InvertersInverters with or without transformers may be used.2.4 Electrical layout2 PLANNING