QOLSYS IQ SHOCK MINI-S Installation Manual

Also see for IQ SHOCK MINI-S: Quick install guide

QOLSYS IQ SHOCK MINI-S Installation Manual Manual pdf 1 page image

IQ SHOCK MINI-S INSTALLATION MANUAL• Reed Switch• Advanced accelerometer basedshock detection• 5 distinct sensitivity settings• LED for easy calibration• Ultra small form factor• Easy to install batteries• Supervisory health messagingPRODUCT FEATURESIQ SHOCKMINI-STECHNICAL SPECIFICATIONSQolsys Inc. proprietary.Reproduction without permission is not permitted.IMPORTANT NOTE:The IQ Shock is intended to be installed on doors with or without glass inserts andon window frames but not on the actual glass surface.MAGNET✓Exterior Doors✓ SlidingglassdoorsWindows✓✓✓CHOOSEINSTALLATIONLOCATIONTwo dip switches allow you to customize the behavior of this device:STEP2 DIPSWITCHCONFIGURATIONSTEP1DS#1 - Installer Test Mode:- Calibrates accelerometer orientation.- LED is Active for dialing in shocksensitivity with potentiometer.- Please note, when test mode is enabled(ON) the IQ Shock Mini will NOT transmitsignals to the compatible panel. Thismode is only used for initial installationand calibration of the shock sensor.ON:OFF: - Disables installertest mode.DS#2 - Reed Switch:ON:OFF:- Enables reed switch (must be ON for ULinstallations).- Disables reed switch.SENSITIVITYLEVELON1 2MAX MINLEDDIPSWITCHESSensitivity Level:CLOCKWISE:COUNTER-CLOCKWISE:- More Sensitive- Less SensitiveSensor: 2.5”H x 1”W x .5”DCode outputs: tamper, tamper restore, alarm, alarm restore, low battery.Transmitter frequency: 319.5 MHzSupervisory keep-alive interval: 70 minutes.RF Peak field strength: typical 36000 uV/m at 3mUL/ULC listed for residential use onlyOperating Temperature: 0C~49CRelative Humidity: 5-93% Non-CondensingStorage Temperature: -25-70CFor use indoor, in dry, ordinary locations only.Door frame height: typical 7ft to 8ft (213 to 244 cm)Door frame width: typical 1ft to 4ft (30.5 to 122 cm)Door frame thickness: 1 1/2" to 1 3/4" (3.8 to 4.4 cm)- IQ Shock Mini-S can be installed on sliding glass doors,windows, doors that swing and more.- Enclosure base is secured to the installation surface withdouble sided tape, manufactured by 3M, part number 4945,UL recognized under file MH17478 (QOQW2).- UL/ULC NOTE:The IQ Shock Mini - S has been listed by UL/ULC forresidential applications only and in accordance with therequirements in the Standards UL 634 and UKLC/ORD-C634 for Door and Window Contact with supplementaryShock Sensor. The shock sensor is for supplementarydetection only and not for primary protection of the surfaceand is not intended for use as a glass break detector.Battery Life Expectancy: 5 years (for typical use) with all sensorsenabled. (Not tested by UL/ULC). Replace battery with exactreplacement, 3V Panasonic CR2032 Lithium (x2). Low batterythreshold (2.55v). Note: For UL/ULC certified installations replacebattery yearly.MAINTENANCE CAUTION!This product uses Lithium Batteries. Improper handling of lithiumbatteries may result in HEAT GENERATION, EXPLOSION or FIRE,which may lead to personal injuries.WARNING! DANGER OF EXPLOSION IF BATTERIES ARE INSTALLEDINCORRECTLY. REPLACE ONLY WITH THE SAME OR EQUIVALENTTYPE RECOMMENDED BY THE MANUFACTURER. KEEP AWAY FROMSMALL CHILDREN: IF SWALLOWED PROMPTLY SEE A DOCTOR. Donot try to recharge these batteries.

/ 2

Related manuals for QOLSYS IQ SHOCK MINI-S