Quickie QM-710 BD Owner's Manual

Contents

Quickie QM-710 BD Owner's Manual Manual pdf 13 page image

VII. WARNINGS: COMPONENTS & OPTIONSQ M- 710/715HD/ 720135. Remain Clear During Power Accessory OperationPlease stay clear of any powered actuator while the compo-nent is in motion. Sunrise power mechanisms move overlarge ranges of travel. Users should be aware of their sur-roundings while components are in motion.6. Maximum User WeightDo not exceed the weight capacity for your specificchair/seating system configuration. Doing so could result inpremature failure or injury.7. Latch ModeWhile operating any power seating function in latched modeuse caution. In latch mode, powered seating will not stopuntil a reverse command is performed or the end of travel ismet.R. CG TILT POWER ACCESSORYWARNINGThe powered CG Tilt accessory for this chair has a maximum userweight capacity of up to 300 lbs for the QM-710 & QM-720,350 lbs for QM-715 with SEDEO Ergo or 3.7, or 400 lbs for theQM-715HD and ASAP Seating. Never exceed this capacity whileoperating the power actuator.S. POWER RECLINEWARNINGPinch PointAvoid putting hands or fingers near the power recline mechanismwhile in operation.Weight CapacityThe maximum user weight capacity for the power recline is up to350 lbs. Exceeding this weight capacity could lead to injury and/orpermanent damage to the equipment.T. LIFT & LIFT/TILT COMBOWARNINGThe powered lift and/or lift/tilt modular accessory for this chairhas a maximum user weight capacity of up to 300 lbs. Neverexceed this capacity while operating the powered actuator.WARNING1. If possible and feasible, the rider should transfer to the(OEM) original Equipment Manufacturer vehicle seat and usethe vehicle restraint.2. If the wheelchair is used for transport, it must be used in aforward-facing seating position.3. The rider must not weigh more than 300 lbs.4. Use only with Wheelchair Tie-down and Occupant RestraintSystems (WTORS) that have been installed in accordancewith the manufacturer’s instructions and SAE J2249.5. Attach WTORS to securement points (A) (B) in accordancewith the manufacturer’s instructions and SAE J2249.6. Attach occupant restraints in accordance with themanufacturer’s instructions and SAE J2249.7. Ensure hip guides are mounted to lock in place.8. Use only Wheelchair Tie-down (A, B) and OccupantRestraint Systems (WTORS) which meet the requirementsof SAE J2249 Recommended Practice– Wheelchair Tie-downand Occupant Restraint Systems For Use in Motor Vehicles.Do not use WTORS designed to rely on the wheelchairstructure to transfer occupant restraint loads to the vehicle.9. The wheelchair has been dynamically tested in a forward-fac-ing mode for a 30 mph frontal impact test. The wheelchairmust be forward-facing during transport.10. In order to reduce the potential of injury to vehicle occu-pants, wheelchair-mounted accessories, such as trays andrespiratory equipment, should be removed and secured sep-arately.11. Postural supports and positioning devices should not berelied on for occupant restraint.12. Do not alter or substitute wheelchair frame parts, compo-nents or seating.13. Sudden stops or impacts can structurally damage your chair.Chairs involved in such incidents should be replaced.V. TRANSIT OPTION AND USE ARefer also to the “Motor Vehicle Safety” warning section for addi-tional transit option and motor vehicle warnings.Transit use does not apply to the QM-715HD.ABAIf these errors occur, tracking will be disabled and the chair will continue todrive but at a reduced speed.1. Check the motors, cables, and connections to the control system.2. You may need to reset this fault by switching the control system off andon again.3. If the trip is still present after the above checks have been made, then theMotor or Module may be defective. Consult your Authorized Dealer forservice.U. SURETRACYour chair may be fitted with SureTrac drive tracking. Theelectronic controller monitors the connectivity of the drive motorsand in the event of a fault will signal the joystick display with one or3 error messages:1. 2001 - M1 Sensor Error - The Power module cannot detect anEncoder Module connection to M12. 3C00 - M2 Sensor Error - The Power module cannot detect anEncoder Module connection to M23. EM Disconnected - The Power module cannot detect anEncoder Module fitted when the parameter Encoder Fitted toYes.MK-100158 Rev. GMK-100158 Rev G