1of2Assembly Instruction Sheet #IS-LLE8407WTFor Style LLE8407WT6 CORPORATE PARKWAYGOOSE CREEK SC 29445www quoizel com, .. .Package ContentsA Crossbar Assemblyx 12017 QuoizelInc. ReleasedDate:2017-09-14Thank you for purchasing a Quoizel product.Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184or visit us on-line at www.quoizel.comFixture Bodyx 1CBAlternateMounting screwx 2FPlease go to for product cleaning tips. Go to the selection.(1) A19 Medium Base Bulb 100W Maximum or(1) Medium Base Vintage Bulb is recommended but not supplied.30-45 minutesIdentify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts arepresent. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacementparts.www.quoizel.com Care + MaintenanceLight Source:Estimated Assembly Time:Preparation:Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.Warnings and CautionsTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We stronglyrecommend that a licensed, professional electrician perform the installation.Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.Figure 2(Step 2 Continued)and secure with mounting balls. Note: The backplate and FixtureBody (C) should be snug against the wall and held tight with themounting balls. If it is not, adjust the length of the mounting screwsor alternate short mounting screws on the Crossbar Assembly (A) byunscrewing the preassembled hex nut and lock washer and thenscrewing the mounting screws or alternate short mounting screws inor out of the crossbar until the correct length is achieved. Once thebackplate and Fixture Body (C) is secure, remove the mounting balland Fixture Body (C) and proceed to Step 3.Hex Nut andLock WasherCMounting BallAMounting Screwor Alternate ShortMounting ScrewBackplateSTEP 3 - Wire ConnectionsA. Wrap bare or green ground wire around green ground screw on thecrossbar, no less than 2 inches from the end of the wire. Tighten thegreen ground screw.B. Use standard wire connectors (not included) to make all wireconnections. Twist connectors until wires are tightly joined together.Wrap each connection with approved electrical tape and carefullystuff all the connected wires into the Outlet Box.Figure 3Green Ground Screwon the CrossbarWhite wirefrom outlet box White wirefrom fixtureBlack wire fromoutlet box (or Red)Black wirefrom fixtureBare, or GreenGround wirefrom outlet boxGround wirefrom FixtureGlass Holderx 1DLock Ballx 2GlassShadex 1ESTEP 1 Install Crossbar Assembly-.A. Pass the supply wires through the Crossbar Assembly (A). Attachthe Crossbar Assembly (A) to the Outlet Box with the head of theGreen Ground Screw facing you. Secure it with Outlet Box Screws(not included). Tighten until snugNote: Use the Alternate Shorter Mounting Screw (B) if yourinstallation requires a shorter mounting screw.Supply Wires withGround WireOutlet Box Screws(not included)Outlet BoxFigure 1AMounting Screwor Alternate ShortMounting ScrewSTEP 2 - Test Fit the Backplate to the Crossbar AssemblyA. Remove the mounting balls from the Crossbar Assembly (A). Placethe backplate and Fixture Body (C) onto the Crossbar Assembly (A)