RCA D40W20YX1 User Manual

Contents

RCA D40W20YX1 User Manual Manual pdf 16 page image

Using th( Remot ControlVCR1 Puts the remote in VCR1 mode and, if Autotuning is enabled, will turn on the TV and tune to the correctinput channelVCR2 Puts the remote in VCR2 mode and, if Autotuning is enabled, wii[ turn on the TV and tune to the correctinput channelVOL - or VOL + Decreases or increases the IV's volume,ZOOM+ or ZOOM- When watching IV, changesthe current format of the screen (4x3, Zoom 1419,Zoom 1619,Zoom 16/9 _Iv, Cinerama, regular mode 1619).Using the INPUT ButtonUsethe INPUTbutton to scroll through the available input channels and view components you have connected tothe IV.I. PressIV to place the remote in IV mode. Make sure the component you want to view is turned ON.2. PressINPUTto tune to an available input channel.3. To return to the channel you were previously watching on IV, pressCH+ or CH- button,VCR1 ON= OFF TV •_VD VCff2 AUX SAT=CABLEIndicator_EVE_SEPLaYYou'lluse these buttons when you programtheremote.#nportun b Theremote,may not he compatible with eftmodelsof ull brandsof components, it ol5o muy notoperute aft functions of the remote thut came withyour componenLTipTostop the uutomatic code 3eurchwithout programmingany components, press and hold CLEARuntit the indicatoron the remote turns off.Programming the Remote to Operate Other ComponentsThe universal remote can be programmed to operate most brands of remote controllablecomponents. The remote is already programmed to operate most RCA, GE, and Proscancomponents.Also, the AUX button can be programmed to operate most brands of an additional remote-controllable component,Note: TheIV button can't beprogrummed on this remote,.Find Out If You Need to Program the RemoteTo determine whether the universal remote needs to be programmed for your component, turnthe component ON. For example, to program the remote for a VCR, turn on the VCR. Point theremote at the VCR, and press the VCR1 button, Then press ON,OFF or CH + (channel up] or CH -(channel down) to see if the VCR responds to the remote commands, If the component does notrespond, the remote needs to be programmed,Programming the RemoteThere are two ways to program the remote controhautomatic code searchdirect entryUsing Automatic Code SearchThe following instructions can be used to program the remote to operate each of yourcomponents. If you want to stop the automatic code search without programming any of yourcomponents, press CLEAR until the indicator on the remote turns off.I. Turn on the component you want to operate (VCR, DVD player, eta,)2. Press and hold the component button you want to program (VCR1, DVD, eta,), While holdingthe component button, press and hold ON,OFF until the indicator on the remote turns on,then release both buttons,3. Point the remote at the component. Press and release PLAY, then wait 5 seconds or until theindicator on the remote stops flashing,At this point the remote is searching for the correct code to program. If, after 5 seconds, thecomponent you want to operate does not turn off, press PLAY again to tell the remote tosearch the next set of codes.Continue pressing PLAY until the component turns oft or you have searched through all ofthe codes. There are 20 total sets of codes, If the component does not turn off after pressingPLAY 20 times, then the remote can't be programmed to operate that component,If the component you want to control does turn off:I. Press and release REVERSE,then wait 2 seconds, Repeat this step until the device turns backON.2. To finish, press and hold STOP until the indicator on the remote turns off,14 Graphics confined within this publication ore for representation only. Cha_te_" 2