Radio Systems CT-2002 Desktop GPS Manual
                         | |
FOR MASTER TIME SYNC VIA TOP-of-HOUR RESETwire timer displays Top-of-Hour in for accurate time readout.Note: T.O.H. input must be used to offset timer by one or moreseconds. Use IR remote control progam option 10 consultmanual page 11 for more information.SERIAL INPUTTERMINATIONRJ-45 OUTRJ-45 INGND+15V DC INRJ-45 SHIELD TO GND1 2 3 4 56 7 8 9 1011121314151617181920GNDSERIAL OUT -SERIAL OUT +GNDSTART SWITCHSTOP SWITCHRESET SWITCHMODE SWITCHGNDTIME CLOSURE 1TIME CLOSURE 2TIME CLOSURE 3TIME CLOSURE 4GNDDOWN TIME CLOSURE AT “0”TOH RESET INPUTRJ-45 OUTRJ-45 IN9V DC INMODEL CT-2002 DESKTOP Part No. 14409SERIAL IN +SERIAL IN -RJ-45 SHIELD TO GNDLogan Township, New Jersey USA1-856-467-8000 • www.radiosystems.comCT-2002 4” & 2” or Desktop (Desktop Shown)GNDSERIAL OUT -SERIAL OUT +GNDSTART SWITCHSTOP SWITCHRESET SWITCHMODE SWITCHGNDTIME CLOSURE 1TIME CLOSURE 2TIME CLOSURE 3TIME CLOSURE 4GNDDOWN TIME CLOSURE AT “0”TOH RESET INPUTRJ-45 OUTRJ-45 IN9V DC INMODEL CT-2002 DESKTOP Part No. 14409SERIAL IN +SERIAL IN -RJ-45 SHIELD TO GNDLogan Township, New Jersey USA1-856-467-8000 • www.radiosystems.comCT-2002 4” & 2” or Desktop (Desktop Shown)Ancillary I/O16- Ground17- Down Time Closure at “0”18- Top-of-Hour Input19- Ground20- +15V DCRemote Control6- Ground7- Start8- Stop9- Reset10- ModeClock Triggers11- Ground12- Time Closure #113- Time Closure #214- Time Closure #315- Time Closure #4Serial Synchronizing Data1- Serial In +2- Serial In -3- Ground4- Serial Out -5- Serial Out +REMOTE CONTROL BARRIER STRIP PIN-OUTSCT-2002 LargeFOR MASTER TIME SYNC VIA RADIO SYSTEMS or SMPTE SERIAL DATAwire timer displays serial in with Radio Systems or SMPTE Time-of-Dayserial input for accurate time readout. Accurate time will be read by allserially connected displays. Time may be offset by one or more hours- use IR remote control progam option 4 consult manual page 10 formore information.Use a straight thru RJ-45 patch cable (from either RJ-45 connector) ifthis clock is being fed with remote master time sync and if downstreamdisplays are not required to display remote timer information.Repeat up to 35 displays.Note: final display serial line must be terminated with a150Ω resisitor (use terminator DIP switch on large clock.)Use a crossover RJ-45 patch cable to slave Time-of-Dayand/or timer displays to downstream units.Via the IR remote control enter the program mode and select option 3 for serialtime-of-day format. Select “rs1” for time-of-day only re-display from the masterclock. Select “rs2” for time-of-day and timer re-display from the master clock.You must use a crossover RJ-45 patch cable if this display is themaster (first clock) in the serial chain or, if you want downstreamclockcs to display remote timer as well as Time-of-DayPC Clock Input SyncNote: Software/hardwarekit available (Radio Systemspart # CT-SYNC) to updateWindows PC clocks via USBfrom the CT-2002serial data streamRadio Systems, Inc. CT2002 ManualPage 20Serial Clock/Timer Connections between CT2002 stand-alone ModelsMaster/Slave Interconnection via RJ-4 Patch Cable ConnectionsStraight thru (Time-of-Day only)RJ-45 Display Cable.Crossover (Time-of-Day and Timer)RJ-45 Display Cable.RJ-45 Patch Cord Wiring |
Related manuals for Radio Systems CT-2002 2" GPS
manualsdatabase
Your AI-powered manual search engine