Regency Liberty L676-NG1 Owners & Installation Manual

Contents

Regency Liberty L676-NG1 Owners & Installation Manual Manual pdf 8 page image

Regency ® L676-1 Direct Vent Gas Fireplace 7INSTALLATION12) Installation and any repairs to this applianceshould be done by an authorized serviceperson. A professional service person shouldbe called to inspect this appliance annually.Make it a practice to have all of your gasappliances checked annually.13) Do not slam shut or strike the glass door.14) Under no circumstances should any solidfuels (wood, paper, cardboard, coal, etc.)be used in this appliance.15) The appliance area must be kept clear andfree of combustible materials, (gases andother flammable vapours and liquids).INSTALLATIONCHECKLIST1) Locate appliancea) Room location (Refer to "Locating YourGas fireplace" section)b) Clearances to Combustibles (Refer to"Clearances" section)c) Mantle Clearances (Refer to "MantelClearances" section)d) Framing & Finishing Requirements(Refer to "Framing & Finishing"section)e) Venting Requirements (Refer to"Venting" section)2) Assemble Top and Side Standoffs (Refer to"Unit Assembly Prior to Installation).3) Install batteries; four "AA" batteries in thewall mounted receiver; three "AAA" batteriesin the remote control and one "AA" batteryinto the DC Sparker. (Refer to remote controlmanual for operating instructions).4) Convert to propane if desired (Refer to"Conversion from NG to LP" section).5) Slide unit into place.6) Install vent (Refer to "Venting Arrangement"sections).7) Make gas connections (Refer to "Gas LineInstallation section).8) Test the pilot (Refer to "Pilot Adjustment"section).Emissions from burning wood or gas couldcontain chemicals known to the State ofCalifornia to cause cancer, birth defects orother reproductive harm.INSTALLATIONIMPORTANT MESSAGESAVE THESEINSTRUCTIONSThe L676-1 Direct Vent Fireplace must beinstalled in accordance with these instructions.Carefully read all the instructions in this manualfirst. Consult the "authority having jurisdiction" todetermine the need for a permit prior to startingthe installation. It is the responsibility of theinstaller to ensure this fireplace is installed incompliance with manufacturers instructions andall applicable codes.BEFORE YOU STARTSafe installation and operation of this appliancerequires common sense, however, we arerequired by the Canadian Safety Standardsand ANSI Standards to make you aware ofthe following:YOUNG CHILDREN SHOULD BECAREFULLY SUPERVISED WHENTHEY ARE IN THE SAME ROOM ASTHE APPLIANCE.CLOTHING OR OTHER FLAMMABLEMATERIAL SHOULD NOT BE PLACEDON OR NEAR THE APPLIANCE.INSTALLATION AND REPAIR SHOULDBE DONE BY AN AUTHORIZEDSERVICE PERSON. THE APPLIANCESHOULD BE INSPECTED BEFOREUSE AND AT LEAST ANNUALLY BY APROFESSIONAL SERVICE PERSON.MORE FREQUENT CLEANING MAYBE REQUIRED DUE TO EXCESSIVELINT FROM CARPETING, BEDDINGMATERIAL, ETC. IT IS IMPERATIVETHAT CONTROL COMPARTMENTS,BURNERS AND CIRCULATING AIRPASSAGEWAYS OF THE APPLIANCEBE KEPT CLEAN.DUE TO HIGH TEMPERATURES, THEAPPLIANCE SHOULD BE LOCATEDOUT OF TRAFFIC AND AWAY FROMFURNITURE AND DRAPERIES.WARNING: FAILURE TO INSTALL THISAPPLIANCE CORRECTLY WILL VOIDYOUR WARRANTY AND MAY CAUSEA SERIOUS HOUSE FIRE.CHILDREN AND ADULTS SHOULD BEALERTED TO THE HAZARDS OF HIGHSURFACE TEMPERATURES, ESPE-CIALLY THE FIREPLACE GLASS, ANDSHOULD STAY AWAY TO AVOID BURNSOR CLOTHING IGNITION.GENERAL SAFETYINFORMATION1) The appliance installation must conformwith local codes or, in the absence of localcodes, with the current Canadian or NationalGas Codes, CAN1-B149 or ANSI Z223.1Installation Codes.2) The appliance when installed, must beelectrically grounded in accordance withlocal codes, or in the absence of local codeswith the current National Electrical Code,ANSI/NFPA 70 or CSA C22.1 CanadianElectrical Code.3) See general construction and assemblyinstructions. The appliance and vent shouldbe enclosed.4) This appliance must be connected to thespecified vent and termination cap to theoutside of the building envelope. Never ventto another room or inside a building. Makesure that the vent is fitted as per Ventinginstructions.5) Inspect the venting system annually forblockage and any signs of deterioration.6) Venting terminals shall not be recessed intoa wall or siding.7) Any safety glass removed for servicingmust be replaced prior to operating theappliance.8) To prevent injury, do not allow anyone whois unfamiliar with the operation to use thefireplace.9) Wear gloves and safety glasses for protectionwhile doing required maintenance.10) Be aware of electrical wiring locations inwalls and ceilings when cutting holes fortermination.11) Under no circumstances should thisappliance be modified. Parts that have to beremoved for servicing should be replacedprior to operating this appliance.