Regency U31-NG10 Owners & Installation Manual

Also see for U31-LP10: Owners & installation manual

Regency U31-NG10 Owners & Installation Manual Manual pdf 24 page image

24 | Regency U31-10 Gas Fireplace Insert|24operating instructionsOPERATINGINSTRUCTIONSBefore operating this appliance, proceed throughthe following check list.1) Read and understand these Instructions beforeoperating this appliance.2) Check to see that all wiring is correct andenclosed to prevent possible shock.3) Check to ensure there are no gas leaks.4) Make sure the glass door is in place. Neveroperate the appliance with the door glassremoved.5) Verify that all venting and the cap is unob-structed.6) Verify log placement. If the pilot cannot be seenwhen lighting the unit - the logs or the embershave been incorrectly positioned.7) The unit should never be turned off and onagain without a minimum of a 60 second wait.8) When lighting the appliance, the inside of theglass may fog up. This will burn off after a fewminutes of operation.OPTIONAL WALLTHERMOSTATA wall thermostat may be installed if desired. Con-nect the wires as per the wiring diagrams. Notethat the wires are connected to the "TH" on thegas valve. Use table on page 14 to determine themaximum wire length:Note: Preferable if the thermostat is installedon an interior wall.FPI offers an optional programmable thermostatbut any 250-750 millivolt rated non-anticipatortype thermostat that is CSA, ULC or UL approvedmay be used.CAUTIONDo not connect the millivoltremote control wires tothe 120V wires.FINAL CHECKBefore leaving this unit with the customer, theinstaller must ensure that the appliance is firingcorrectly. This includes:1) Clocking the appliance to ensure the correctfiring rate (rate noted on label) at 15 minutes.2) If required, adjusting the primary air to ensurethat the flame does not carbon. First allow theunit to burn for 15 min. to stabilize.CAUTIONAny alteration to the product that causes soot-ing or carboning that results in damage to theexterior facia is not the responsibility of themanufacturer.Thermostat Wire TableRecommended Maximum Lead Length(Two-Wire) When Using WallThermostat (CP-2 System)Wire Size Max. Length14 GA. 50 Ft.16 GA. 32 Ft.18 GA. 20 Ft.20 GA. 12 Ft.22 GA. 9 Ft.CAUTIONDo not connect the millivoltwall thermostat wiresto the 120V wires.FIRST FIREThe first fire in your stove is part of the paint curingprocess. To ensure that the paint is properly cured,it is recommended that you burn your fireplace for atleast four (4) hours the first time you use it with thefan on. When first operated, the unit will release anodour caused by the curing of the paint, the burn-ing off of any oils remaining from manufacturing.Smoke detectors in the house may go off at thistime. Open a few windows to ventilate the room fora couple of hours.The glass panel may require cleaning after the unithas cooled down.DO NOT AT TEMPT TO CLEAN THE GLASSWHILE IT IS HOT.Note: When the glass is cold and the applianceis lit, it may cause condensation and fogthe glass. This condensation is normaland will disappear in a few minutes asthe glass heats up.DO NOT BURN THE APPLIANCE WITHOUTTHE GLASS FRONT IN PLACE.820 Valve Description1) Gas on/off knob2) Manual high/low adjustment3) Pilot Adjustment4) Thermocouple Connection5) Main Operator6) Outlet Pressure Tap (Manifold Pressure)7) Inlet Pressure Tap (Supply Pressure)8) Pilot Outlet9) Main Gas Outlet10) Flange Securing Screw Holes11) Alternative TC Connection Point12) Thermoelectric Unit13) Additional Valve Mounting Hole