Saeco HD8321/01 Operating Instructions Manual

Also see for HD 8323: Operating instructions Operating instructions

Contents

• 18 •selection knob (17) to the " " position and close the knob(3) by turning it clockwise.• (Fig.3) - Fill the tank with fresh drinking water.• (Fig.13-14) - Insert the filter holder into the brew unit (8)from the bottom and turn it from left to right until it locksinto place.• (Fig.15) - Place a suitable container under the filterholder.• (Fig.16) - Turn the selection knob (17) to the " " positionand dispense all the water in the tank.(Fig.17) - Once the tank is empty, stop dispensing andswitch the selection knob (17) to the " " position.• Fill the tank again and wait until the "machine ready" light(20) turns on.• (Fig.19) - Remove the filter holder from the unit by turningit from right to left and rinse it with fresh drinking water.The machine is now ready; please see related sections foroperating details on how to brew coffee and dispense steam.5 COFFEE BREWINGWarning! During the coffee brewing it isforbidden to remove the pressurized filterholder by manually turning it clockwise. Danger ofburns.• During this operation, the "machine ready" light (20) mayflash; this is to be considered as a standard and not a faultyoperating mode.• Before using the machine, make sure that the hot water/steam knob (3) is closed and that there is enough water inthe tank.• (Fig.3) - Press the ON/OFF button (11) and switch it to the"I" position.• Wait until the "machine ready" light (20) turns on. Themachine is now ready for coffee brewing.Accessories for coffee brewing are placed ina specially designed seat to make operationseasy and immediate.If the ground coffee measuring scoop and/or the filtersare required, lift the cover (2) and take what you need(Fig.35 e Fig.36).5.1 Using Ground Coffee• (Fig.7) - Insert the filter (14) in the pressurized filter holder(12); the filter is already inserted when using the machinefor the first time.• (Fig.13) - Insert the filter holder into the brew unit (8) fromthe bottom.• (Fig.14) - Turn the filter holder from left to right until itlocks into place. Release the pressurized filter holder grip.The handle will slightly turn to the left. This movementguarantees proper filter holder performance.• (Fig.16) - Preheat the pressurized filter holder by switchingthe selection knob (17) to the " " position until somewater spills out of it. This is to be done only for the firstcoffee brewing.• (Fig.17) -When 150 cc of water have flowed out, set theselection knob (17) to the " " position to stop brewing.• (Fig.19) - Remove the filter holder from the machine byturning it from right to left and pour out any water left. Asthe machine is fitted with the special filter (14), there is noneed to change the filter to make one or two coffees.• (Fig.35) - Remove the measuring scoop from themachine.• (Fig.8) - Add 1-1.5 measuring scoop(s) for single coffeeand 2 measuring scoops for double coffee. Remove anycoffee residues from the rim of the filter holder.• (Fig.13) - Insert the filter holder (12) into the brew unit (8)from the bottom.• (Fig.14) - Turn the filter holder from left to right until itlocks into place.• (Fig.15) - Take 1 or 2 preheated cups and place themunder the pressurized filter holder. Make sure that they arecorrectly placed under the coffee brewing nozzles.• (Fig.14) - Switch the selection knob (17) to the " "position.• When the desired quantity of coffee has been obtained,turn the selection knob (17) to the " " position to stopcoffee brewing. Wait a few seconds after brewing hasstopped, then remove the cups of coffee (Fig.18).• (Fig.19) - Remove the pressurized filter holder and emptyout the remaining coffee residues.Note: If a small quantity of water remainsin the filter holder, this has to be consideredas absolutely normal and is due to the filter holderfeatures.Important Note: The filter (14) should be keptclean to guarantee perfect results. Clean dailyafter use.