Saeco Royal SUP 015 User's And Maintenance Booklet

Also see for Royal Digital SUP 015: User's and maintenance booklet User's and maintenance booklet User's and maintenance booklet

Contents

Saeco Royal SUP 015 User's And Maintenance Booklet Manual pdf 17 page image

333226 Remove the water tank (11) from themachine, remove its cover (12) and fill it withcold water (approx. 2.4 l). A valve on the tankbottom prevents water from escaping.Before installing the water tank in themachine, make sure the coffee beancontainer cover is properly fitted.Install the water tank, slightly pressing over it tofit the valve which will open automatically.Replace the cover on the tank.Do not fill the tank with an excessivequantity of water.Always fill the tank with fresh water:hot water as well as other fluidsmight damage the tank.Do not switch on the machine if thewater tank is empty. Before usingthe machine make sure there is enough water inthe tank.Connect the plug to the socket and press themain switch.The display showsShould (1/2) be displayed,press the Energy saving switch to disactivate theenergy saving mode.DrainageDirect the steam/hot water dispensing tube (7)over the drip tray (2). Place a cup or anothersuitable container under the dispensing tube,then turn the steam/hot water knob (9)counterclockwise. The pump starts automati-cally. Wait until a regular water jet is obtained,then close the knob. The machine is nowdrained and ready to work.The display showsImportant: It is advisable to drain the machinebefore the first start, after a prolonged periodthe machine has not been used or whenever thewater tank has been completely emptied. Fur-thermore, should the pump be defective, thedisplay showsProgrammingthe coffee machine27 To enter the programming mode, press thekey ENT (pre-ground coffee) when the machineis on and keep it pressed until the first two linesof the programming mode are displayed:At the end of the line appears a blinkingasterisk, which can be moved up and downwith the keys (tall and regular coffee).The display shows the following items in thissequence:LANGUAGE PREGRINDINGRINSING CYCLE FUNCTION TOTAL COFFEEWATER HARDN. DESCALINGCUP HEATER SIGN. DESCAL.TEMPERATURE TIMERPREBREWING RISING CYCLEThen, press ESC. The machine is now in thenormal mode again.Selecting menu itemsSelect the different menu items by means of thekeys . The key ENT allows you toactivate the selected item. It is possible tomodify the selected figures in a menu item usingthe keys . The key ENT memorizes theselected options, for instance <> for theitem cup heater.Should you accidentally change some data,press ESC to leave the menu item without savingthe new options which were selected acciden-tally.Selecting the languageMove the asterisk at the end of the line to themenu item <> using the keys. Press ENT to activate this item.The display shows:The keys allow you to change the setoptions: italiano, français, Deutsch, english,español, português.Rinsing cycle functionIf the rinsing cycle function is activated, themachine that is started after a period of inactiv-ity starts a water rinsing cycle to the coffeedispensing units automarically.Move the asterisk to the menu item <cycle>> using the keys und press ENT toactive it.The display shows:You can modify the chosen item with thekey : on; off.Water hardness adjustmentIn order to adjust the water hardness, it isnecessary to test the water using the stripsupplied with the machine. Dip the strip into thewater for a second, shake off excess watergently, wait approx. 1 minute and read theresults.Move the asterisk at the end of the line to themenu item <> using the keys. Press ENT to activate this item.The display shows:Activating the cup heaterMove the asterisk at the end of the line to themenu item <>. Press ENT toactivate this function.The display shows:The keys allow you to change the setoptions: on, off.Selecting temperatureMove the asterisk at the end of the line to themenu item <> using thekeys . Press ENT to activate this item.The display shows:The keys allow you to change the setoptions: minimum, low, medium, high, maxi-mum.Selecting the prebrewingfunctionAs soon as the coffee has been moistened, thepump stops for a while. Then, the brewing cyclecontinues.Move the asterisk at the end of the line to themenu item <> using the keys. Press ENT to activate this function.The display shows:WARMING UPENERGYSAVINGHOT WATERREADY FOR USEVENTILATE1 LANGUAGEENGLISH3 CUP HEATERON4 TEMPERATUREMEDIUM5 PREBREWINGONDRAINAGESELECTING THE LANGUAGELANGUAGEWATER HARDNRINSING CYCLEON2 WATER HARDNHARDNESS 2Sehr weiches WasserWeiches WasserMittleres WasserHartes WasserHardness 4Hardness 3Hardness 2Hardness 1The keys allowyou to change the setoptions:hardness 1 (verysoft), hardness 2 (soft),hardness 3 (medium),hardness 4 (hard).