18 19Technical specifications - CT ForceGeneral specifications – CT Xtra & CT BathroomApplicationsAll Salamander pumps are designed to boost low pressure hot and cold supplies fromcistern-fed services. When supplies from a water heater or a combination boiler are to beboosted contact the Salamander PumpWise helpline on 0191 516 2002 for guidance.Voltage230 volts, 50 Hz.Motor typeCapacitor start and run induction type motor with stainless steel shaft and in-built resettingthermal protection (complies with BS5000 part 11).Maximum headAll CT Xtra and CT Bathroom pumps are rated for a maximum static head of 10 metres.(100 kPa / 1.0 bar)Anti-vibration couplersDo not bendPlease refer to the Technical Specifications table for information on which AV Couplers aresupplied with each pump.Mechanical sealsRotary mechanical face seals are used. Scale deposits in water supplies can cause themechanical seal to stick if left for long periods without use. The pump must be run for at leastfive minutes every four weeks to ‘exercise’ all working parts.Connections¾” BSP male.InitiationOnly applies to positive head pumps. Fully automatic, flow operated, requiring 1 litre in 30 secper side or 2 litres in 30 sec mixed.TemperatureMaximum fluid temperature 60ºC.Pump noiseSalamander has engineered this product range to be as quiet as possible, however no pumpis completely silent. Correct installation (anti-vibration couplers straight, rubber feet fitted)will minimise noise, vibration and transmission noise.Standards and approvalsSplash proof rating IPX2; complies with the requirements ofcurrent British and European safety standards for household andsimilar electrical appliances; meets with Compliance with EuropeanCommunity Directives (CE). Due to continuous improvement andupdating specifications may be altered without prior notice.The CT Xtra and CT Bathroom ranges of pumps are also fully WRASapproved. CT Xtra has also been awarded Quiet Mark.Part No. Description Specification Performance Connection Type Pump Volumetrics Packed PumpVolumetricsElectricalInputPumpTypePump Hoses Isolators Dimensions DimensionsCT FORCEForce 15PTForce 15IPT1.5 Bar Twin EndPositive Head ShowerPump 3A 110(1.1)130(1.3)150(1.5)¾” 22mm21mm 4.96 180 120 160 6.02 298 218 205Force 20PTForce 20IPT2.0 Bar Twin EndPositive Head ShowerPump 3A 150(1.5)180(1.8)200(2.0)¾” 22mm21mm 4.97 180 120 160 6.03 298 218 205Force 30PTForce 30IPT3.0 Bar Twin EndPositive Head ShowerPump 3A 220(2.2)260(2.6)300(3.0)¾” 22mm21mm 6.22 210 120 160 7.34 298 218 205Force 20PSForce 20IPS2.0 Bar Single EndPositive Head ShowerPump 3A 150(1.5)180(1.8)200(2.0)¾” 22mm21mm 4.33 183 120 160 5.17 298 218 205Force 30PSForce 30IPS3.0 Bar Single EndPositive Head ShowerPump 3A 210(2.1)260(2.6)300(3.0)¾” 22mm21mm 5.61 213 120 160 6.48 298 218 205CT FORCE Universal PumpsForce 15TUForce 15ITU1.5 Bar Twin EndPositive and NegativeHead Shower Pump 3A 110(1.1)130(1.3)150(1.5)¾” 22mm21mm 5.53 180 125 315 6.75 298 218 360Force 20TUForce 20ITU2.0 Bar Twin EndPositive and NegativeHead Shower Pump 3A 150(1.5)180(1.8)200(2.0)¾” 22mm21mm 5.57 180 125 315 6.82 298 218 360Force 30TUForce 30ITU3.0 Bar Twin EndPositive and NegativeHead Shower Pump 3A 220(2.2)260(2.6)300(3.0)¾” 22mm21mm 6.79 210 125 315 8.10 298 218 360Force 20SUForce 20ISU2.0 Bar Single EndPositive and NegativeHead Shower Pump 3A 150(1.5)180(1.8)200(2.0)¾” 22mm21mm 4.96 183 125 315 5.94 298 218 360Force 30SUForce 30ISU3.0 Bar Single EndPositive and NegativeHead Shower Pump 3A 210(2.1)260(2.6)300(3.0)¾” 22mm21mm 6.20 213 125 315 7.24 298 218 360Fuse230/1/50RegenerativePressure (kPA/Bar) at 16ltr/minPressure (kPA/Bar) at 8tr/minMax pressure (kPA/Bar) closed headBSPPush FitIsolators intergrated into the hosesWeight (Kg)Length (mm)Width (mm)Height (mm)Weight (Kg)Length (mm)Width (mm)Height (mm)