Salda VSA 3.0 Series Mounting And Installation Instruction

Contents

Salda VSA 3.0 Series Mounting And Installation Instruction Manual pdf 5 page image

EN | 5VSA 3.0_VSA EKO v2019.04Make sure that the electric power chain data complies with the data on the product label on the device case.Selected power cord has to match device power.The fan has to be connected according to the electric scheme which is described in this document and is shown under the electricity connectionbox cap (fig. 12).It is necessary to connect an external protective device (an automatic switch or fuse) with a trigger current 1.5 times higher than the devices max-imum current (indicated on the product label).The unit must be adequately grounded.If the device engine speed control regulator is used, be sure that it ensures safe activity of the engine.It is necessary to ensure minimal engine speed at which the reverse thrust valves (if any) open.Frequency converters for the speed control of these devices are not used.WIRING DIAGRAMYE/GNBKPEN LBNNTK TKRDRDLBUYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,SP1-L-0kProtective earthPE, L1, N - linevoltage 230VCC - capacitorTK - jumperTK - jumperC - capacitorCPE, L1, N - linevoltage 230VProtective earthYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,BULRDRDTKTKNBNLNPEBKYE/GNPE, L1, N - lineProtective earthYE/GN - yelRD - red; BNRNNPEBKYE/GNYE/GNBKPENNRYE/GN - yelRD - red; BNProtective earthPE, L1, N - lineYE/GNBKPEN LBNNTK TKRDRDLBUYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,Protective earthPE, L1, N - linevoltage 230VCC - capacitorTK - jumperTK - jumperC - capacitorCPE, L1, N - linevoltage 230VProtective earthYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,BULRDRDTKTKNBNLNPEBKYE/GNYE/GNBKPENNRYE/GN - yelRD - red; BNProtective earthPE, L1, N - lineYE/GNBKPEN LBNNTK TKRDRDLBUYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,Protective earthPE, L1, N - linevoltage 230VCC - capacitorTK - jumperTK - jumperC - capacitorCPE, L1, N - linevoltage 230VProtective earthYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,BULRDRDTKTKNBNLNPEBKYE/GNYE/GNBKNRYE/GNBKN LBNTK TKRDRD BUCC BURDRDTKTKBNLNBKYE/GNSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kSP1-L-0kYE/GNBNPEN LBUNTK TKRDRDLBKYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,SP2-L-0kProtective earthPE, L1, N - linevoltage 230VCC - capacitorTK - jumperYE/GNBNPEN LBUNRDLYE/GN - yellow/greenRD - red; BN - braun;SP2-L-0kProtective earthPE, L1, N - linevoltage 230VCC - capacitorYE/GNBNPEN LBUNRDLYE/GN - yellow/greenRD - red; BN - braun;SP2-L-0kProtective earthPE, L1, N - linevoltage 230VCC - capacitorYE/GNBNPEN LBUNTK TKRDRDLBKYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,SP2-L-0kProtective earthPE, L1, N - linevoltage 230VCC - capacitorTK - jumperYE/GNBNPEN LBUNTK TKRDRDLBKYE/GN - yellow/green; BK - black,RD - red; BN - braun; BU - blue,SP2-L-0kProtective earthPE, L1, N - linevoltage 230VCC - capacitorTK - jumperYE/GNBNPEN LBUNRDLYE/GN - yellow/greenRD - red; BN - braun;SP2-L-0kProtective earthPE, L1, N - linevoltage 230VCC - capacitorYE/GNBNN LBURDSP2-L-0k CYE/GNBNN LBUTK TKRDRD BKSP2-L-0k C#1 #2GNYE BK RD BU BN- green/yellow - black - red - blue - brown#3 #4PE BK BU BN YE WH RD- green - yellow - black - blue - brown - yellow - white - redP – protective earth,L – phase, mains 50/60 HzN - neutral, mains 50/60 HzAnalog in (0-10V DC/PWM) – speed setting via linear set value (0-10VDC) or PWM signalTacho out – tach output: 1 pulse per revolution+10VDC OUT – voltage output +10V max. 1.1 mAAlarm relay – NC, contact fermé; dans le cas de panne de vient ouvertSTART-UPThe device can be started only by qualified and trained personnel.Before starting the device, make sure that the power chain matches the data on the label.Before starting the device, make sure that the device is connected to the power source in accordance with the scheme shown in this documentand under the electricity connection box cap.Before starting the device, make sure that all the above listed security and installation instructions are arranged.When the device is started, make sure that the engine rotates evenly, does not vibrate and does not emit strange noise.When the device is started, it is necessary to verify that air flow of the device matches the air direction indicated on the case.It is necessary to verify that the current used by the engine does not exceed the maximum current (indicated on the product label).It is necessary to check whether the engine does not overheat.It is prohibited to turn on and turn off the fan so often that it would lead to engine windings overheating or isolation damage.MAINTENANCEFan bearings do not require maintenance.If there are no air filters before the fan, the only maintenance requirement of the fan is impeller cleaning. It is recommended to clean the impellerat least once every six months.