Samsung CLX-3185 User Manual

Also see for CLX-3185: User guide Service manual

Contents

Wireless network setup (CLX-3185FW/CLX-3185WK only)_ 52the machine fails to get the wireless connection. Try again toconnect to the wireless network after solving the connectionproblem.Canceling a wireless network connection process inPBC modeTo cancel the wireless network connection function when the machine isconnecting to the access point (or wireless router) in PBC mode, pressthe WPS ( ) button on the control panel again. The ConnectingCanceled and the Wait 2 minutes for Reconnecting messagesappear in order on the display.Disconnecting a wireless network connection in PBCmodeTo disconnect the wireless network connection, press the WPS ( )button on the control panel again.• When the access point (Wi-Fi Network) is in idle mode: TheDisconnected message appears on the display. The machine isreturned to ready mode.• When the access point (Wi-Fi Network) is being used: The WaitJob to Finish message appears on the display. The machine waitsuntil the current job is finished. Then, the wireless networkconnection is automatically disconnected. The machine is returnedto ready mode.Setting a wireless network in PIN modeFactory default in your machine is PBC mode. To change to PIN mode,refer to "Changing WPS mode" on page 51.Connecting a wireless network in PIN modeTo connect to the wireless network in PIN mode, follow the followingsteps. You also need to check the status of the WPS ( ) button andthe wireless LED.1. Press the WPS ( )Gbutton on the control panel.2. Enter xxxx-xxxx on AP:02:00: Eight-digit PIN number appears onthe displayUGThen, the machine starts waiting for up to two minutesuntil you enter the supplied PIN number on the access point (orwireless router)U3. : Enter the supplied PIN number on the access point (orwireless router) within two minutes.4. Connecting: The machine is connecting to the wireless network.5. Connected: When the machine is successfully connected to thewireless network, the blue wireless LED light stays on.• AP SSID: After completing the wireless network connectionprocess, AP’s SSID information appears on the display.If the machine fails to connect to the wireless network, theConnecting Failed and the Wait 2 minutes forReconnecting messages appear in turn on the display. Then,the machine tries to re-connect to the wireless network.Re-connecting to a wireless network in PIN modeIf you press the WPS ( ) button on the control panel when thewireless function is off, the machine automatically tries to re-connect tothe access point (or wireless router) with the previously used wirelessconnection settings and address.1. Connecting: If you press the WPS ( ) button on the controlpanel when the wireless function is off, the machine automaticallytries to re-connect to the access point (or wireless router) with thepreviously used wireless connection settings and address.2. Connected: When the machine is successfully connected to thewireless network, the blue wireless LED light stays on.• AP SSID: After completing the wireless network connectionprocess, AP’s SSID information appears on the display.If there is no previously used access point (or wireless router),or the network settings have been changed, the ConnectingFailed and the Wait 2 minutes for Reconnecting messagesappear in turn on the display, and then the machine tries tore-connect to the wireless network. After the second attempt toconnect, the machine stops the wireless connection function ifthe machine fails to get the wireless connection. Try again toconnect to the wireless network after solving the connectionproblem.Canceling a wireless network connection process inPIN modeTo cancel the wireless network connection function when the machine isconnecting to the access point (or wireless router) in PIN mode, pressthe WPS ( ) button on the control panel again. The ConnectingCanceled and the Wait 2 minutes for Reconnecting messagesappear in order on the display.Disconnecting a wireless network connection in PINmodeTo disconnect the wireless network connection, press the WPS ( )button on the control panel again.• When the access point (Wi-Fi Network) is in idle mode: TheDisconnected message appears on the display. The machine isreturned to ready mode.• When the access point (Wi-Fi Network) is being used: The WaitJob to Finish message appears on the display. The machine waitsuntil the current job is finished. Then, the wireless networkconnection is automatically disconnected. The machine is returnedto ready mode.SETTING A WIRELESS NETWORK WITH USBCABLERefer to your network administrator or the person that set up yourwireless network for information about your network configuration.Installing the machine on a wireless network with anAccess Point (Windows)Items to prepareEnsure you have next items ready.• Access point• Network-connected computer• Software CD that provided with your machine• The machine installed with a wireless network interface• USB cableCreating the infrastructure network in WindowsWhen the items are ready, follow below steps:1. Check whether the USB cable is connected to the machine.2. Turn on your computer, access point and machine.