Samsung FP-T5084 Owner's Instructions Manual

Also see for FP-T6374: Manual Safety instructions Owner's instructions Owner's instructions Owner's instructions

Contents

English - 19Memorizing the ChannelsYour TV can memorize and store all of the available channels for both air and cable channels. After the availablechannels are memorized, use the CH or CH button to scan through the channels. This eliminates the needto change channels by entering the channel digits. There are three steps for memorizing channels: selecting abroadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).Selecting the Video Signal-sourceBefore your television can begin memorizing the available channels, you mustspecify the type of signal source that is connected to the TV (i.e. an air or a cablesystem).1 Press the MENU button to display the menu.Press the ▲ or ▼ button to select Channel, then press the ENTER button.2 Press the ENTER button select Antenna.Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.Press the EXIT button to exit.Storing Channels in Memory (Automatic Method)1 Press the MENU button to display the menu.Press the ▲ or ▼ button to select Channel, then press the ENTER button.2 Press the ▲ or ▼ button to select Auto Program, then press the ENTERbutton.3 Press the ▲ or ▼ button to select the antenna connection, then press theENTER button.➢ Air: “Air” antenna signal.Cable: “Cable” antenna signal.Air+Cable: “Air” and “Cable” antenna signals.➢ If the antenna is connected to ANT 2 IN (CABLE), select Cable and if it isconnected to ANT 1 IN (AIR), select Air.➢ If both ANT 1 IN and ANT 2 IN are connected, select the Air + Cable.➢ If you selected Air, then go to step 5.4 Press the ▲ or ▼ to select the correct analog signal cable system sourceamong STD, HRC, and IRC, then press the ENTER button. If you have Digitalcable TV, select the cable system signal source for both Analog and Digital.➢ If you have Digital cable TV, select the signal source for both Analog andDigital.➢ STD, HRC, and IRC identify various types of cable TV systems. Contactyour local cable company to identify the type of cable system that exists inyour particular area. At this point the signal source has been selected.5 The TV begins memorizing all available stations.If you want to stop Auto Programming, press the ENTER button. The StopAuto Program? message will be displayed. Select Yes by pressing the ◄ or ►button.Press the EXIT button to exit.➢ The TV must be connected to antenna/cable in order to receive digital TVsignals. Even if a particular channel is deleted from the memory, you canalways tune to that channel directly by using the number buttons on theremote control.➢ • All available DTV and analog channels are automatically stored inmemory.• It takes approximately 3 to 10 minutes to memorize channels.Auto ProgramAuto Program in progress.Cable Channel 6768 %StopEnterAntenna : Air ►Auto Program ►Clear Scrambled Channel ►Channel List ►Name ►Fine Tune ►Signal Strength ►LNA : On ►ChannelT VEnterMoveAuto ProgramT VSelect the antennas to memorize.AirCableAir + CableStartEnterMoveStartStartAuto ProgramStop Auto Program?Yes No68 %Antenna : Air ►Auto Program ►Clear Scrambled Channel ►Channel List ►Name ►Fine Tune ►Signal Strength ►LNA : On ►ChannelT VEnterMove ReturnAntenna : AirAuto ProgramClear Scrambled ChannelChannel ListNameFine TuneSignal StrengthLNA : OnChannelT VEnterMoveAirCableReturnReturnReturnSelect the cable system.Auto ProgramT VEnterMove ReturnSTDHRCIRCAnalogSTDHRCIRCDigitalStartReturnEnterMove Return