Samsung PN50C490B3D Quick Setup Manual

Also see for PN50C490B3D: User manual User manual User manual User manual

Contents

quick setup guide

Step 1: Install the StandFollow the steps below to connect the TV to the stand.✎ NOTEx Make sure to distinguish between the front and back of the Stand andGuide Stand when assembling them.x Make sure that at least two people lift and move the PDP TV.x Stand the product up and fasten the screws. If you fasten the screws withthe PDP TV placed down, it may lean to one side.1 Connect the Guide Stand to theStand using four screws (M4 X L10)as shown.2 With your TV upright, connect theTV to the Stand.3 Fasten two screws (M4 X L12) atposition 1, and then fasten twoscrews (M4 X L12) at position 2.ssssRearFrontssss12Step 2: Install the Batteries into the RemoteTo install batteries into your remote control,follow these steps:1. Lift the cover on the back of the remoteupward as shown in the figure to theright.2. Install two AAA batteries.✎ Make sure to match the + and -ends of the batteries to the diagram in the battery compartment.3. Replace the cover.Step 3: Connect Power and Antenna or CableQuick Setup GuideCongratulations on the purchase of your new Samsung TV.Read this setup guide to get your TV up and running quickly.1-800-SAMSUNG (1-800-726-7864)Samsung Electronics America, Inc.85 Challenger Road Ridgefield Park, NJ 07660-2112Samsung Electronics Canada Inc.55 Standish Court Mississauga, Ontario L5R 4B2Call Center hours of operation: Mon-Sun, 9:00 AM -12AM EST.To register this product, visit: www.samsung.com/register.STOPPlease do not return this unit.If you have problems operating yourTV, call:1-800-SAMSUNG (1-800-726-7864)For web support please visit:www.samsung.com/supportStep 4: Connect External DevicesConnecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)Step 5: Run Plug & PlayWhen you turn on your TV for the first time, it automatically launches the Plug &Play function. With Plug & Play, you can select the On Screen Display language,set the clock mode, and launch the TV’s channel memorizing process.It also displays connection instructions similar to those in this guide.To navigate while Plug & Play is running, press the Up, Down, Left or Right arrowbuttons on your remote. To make a selection, press the ENTERE button.To skip a screen, press the MENU button. To turn on your TV, press the POWERbutton on the remote or on the TV. To run Plug & Play, follow these steps:1 Using your remote control, selectthe language for the On ScreenDisplay (OSD), and then pressthe ENTERE button.P2 Select Home Use, and thenpress the ENTERE button. Ifyou select Store Demo, the TVwill reset your picture and audiosettings every 30 minutes.3 Select the Antenna sourceto memorize, you must selectAntenna Source to same typeas your cable system type. Afterselecting source, select Start;then press the ENTERE buttonon your remote.✎ Most cable systems are Standard(STD) systems, If you are not sure aboutwhat kind of cable system you have, contact your cable company.✎ If your TV is attached to a cable or satellite box, skip Steps 3 through 5. AfterPlug & Play is complete, set your TV to Channel 3 or 4, according to thedirections for your cable or satellite box.4 The TV memorizes the availablechannels. This process can takeup to 45 minutes.5 After the TV has memorized thechannels, choose the ClockMode. Select Auto if you havea digital channel in your area.Select Manual if you don’t, orif you have a cable or satellitebox. When done, press theENTERE button.✎ If you select Manual, theclock setting screen appears.6 Select the daylight savings timesetting: Off, On or Auto and thenpress the ENTERE button.✎ This function is only availablewhen the Clock Mode is set toAuto.7 Select the time zone in which you live, and then press the ENTERE button.8 After the time zone screen, The connection method for best HD screenquality is displayed. Press Right arrow button on your remote to view eachscreen in succession. Press the Blue button to skip this section.9 The Enjoy your TV. screen appears. Then press the ENTERE button.If You Want to Rerun Plug & Play1. Press the SOURCE button on your remote, then select TV mode.2. Press the MENU button on your remote to display the menu.3. Press the ▲ or ▼ button to select Setup, and then press the ENTEREbutton.4. Press the ENTERE button again to select Plug & Play.Connecting an audio device (Home Theater, etc.)Connect your TV to your Home Theater or other audio device to enjoy enhancedSound quality.Connecting a PCConnect your TV to a PC to use it as a Monitor.Top viewFrontRearGuide StandScrews (M4 X L10)StandRearHDMI IN 3HDMI OUTAUDIO OUTVIDEO OUT AUDIO OUTCOMPONENT OUTAUDIO OUTDVI OUTUsing an HDMI to DVI CableHD connection (up to 720p/1080i)Very Good ConnectionDeviceBest ConnectionHD connection (up to 720p/1080i)Using an HDMI CableDVD, Blu-ray player, HD cable box, HD STB(Set-Top-Box) satellite receiverDeviceUsing a Component CableGood ConnectionComponent connection (up to 720p/1080i)DVD, Blu-ray player, cable box,STB satellite receiver, VCR,DeviceUse one of the connections below to connect your TV to an external A/V device. We recommend usingHDMI for the highest picture quality.✎ When connecting to AV IN on the back of your TV, attach the video cable (yellow) to the green jacknext to the AV IN label. The jack will not match the color of the video cable (yellow).U Move E EnterSelect Language of the OSD.Language :Plug & PlayEnglishEspañolFrançaisL Move E EnterSelect ‘Home Use’ when installing this TV in your home.Store Demo Home UsePlug & PlayU Move E Enter m SkipSelect the Antenna source to memorize.AirCableAutoStartStartStartPlug & PlayU Move E Enter m SkipSet the Clock Mode.Clock Mode AutoManualPlug & PlayU Move E Enter m SkipSet to daylight saving time.DSTOffOnAutoPlug & Play48%E Enter m SkipAuto Program in Progress.DTV Air : -- Air : --DTV Cable : -- Cable : -- Cable : 35StopPlug & PlayBN68-03115A-01Lowest Quality ConnectionUsing an Audio/Video CableAudio/Video connection (480i only)DVD, Blu-ray player, cable box, STB satellitereceiver, VCRDeviceVHF/UHF AntennaConnect Ant In to• Wall cable jack• VHF/UHF Antenna• Cable or Satellite boxAnt or Cable OutMake sure the AC power cord is plugged in securely tothe wall outlet and the TV.Use a 75 ohm (round) cable.orAntenna Cable(Not Supplied)HDMI Cable (Not Supplied)HDMI to DVI Cable(Not Supplied)Audio Cable (Not Supplied)Audio Cable(Not Supplied) Component Cable(Not Supplied)Video Cable(Not Supplied)AUDIO INOPTICALAnalog Audio connectionDigital Audio connectionAmplifier / DVD home theaterDigital Audio SystemUsing an Audio CableUsing an Optical CableOptical Cable (Not Supplied)Audio Cable (Not Supplied)DVI OUTAUDIO OUTAUDIO OUTPC OUTHD connectionUsing an HDMI to DVI CableUsing a D-Sub CableHDMI to DVI Cable (Not Supplied)D-Sub Cable (Not Supplied)Audio Cable (Not Supplied)Audio Cable (Not Supplied)

/ 2

Related manuals for Samsung PN50C490B3D