Sandia 80-2500 Safety, Operation And Maintenance Manual With Parts List
            | |
(18) Sniper 12-Gallon, 500 PSI Carpet Extractor Sniper 12-Gallon, 500 PSI Carpet Extractor (7)2.0 Grounding Instructions ContinuedThis electric equipment is for use on anormal 120 volt circuit. It has a groundedplug that looks like the plug illustrated in(Fig A). The use of a temporary adaptor isNOT recommended.NOTE: In Canada, the use of a temporaryadapter is not permitted by the CanadianElectrical Code.3.0 Care of your Carpet ExtractorTreat your machine as you would any other high grade, precision made product.Dropping, unreasonable bumping across thresholds and other misuses may result in adamaged unit which will not be covered under warranty.After each use, wipe the extractor body, accessories and power cord with a slightlydamp cloth. When not in use, the remove the power cord and hoses. Stored in a dryarea.4.0 Set-Up and OperationDO NOT USE ON WET SURFACES. DO NOT EXPOSE TO RAIN. STOREINDOORS.All carpet extractors, no matter what the time of year, are shipped with antifreeze in thesolution lines. Prior to first use, fill the tank with one quart of warm water. Attach thehose and using the hand tool wand, flush out the system by spraying the one quart ofwater through the pump.• Attach the 1-1/2 inch vacuum hose and the brass quick disconnect.• Fill the recovery tank with warm water (less than 100 degrees Fahrenheit). Fill toapproximately 4 inches from the top. Pre-spray a liquid detergent made for carpetcleaning or upholstery on carpet and agitate carpet. Next, use clean water fromsolution tank to extract – this procedure is highly recommended. Note: read and mixyour pre-spray solution to the dilution ratios as directed.• Be sure to replace any filters back into the machine prior to use.• DO NOT use citrus acid, buterol or harsh degreasers inside the machine.• DO NOT use powdered detergents in this machine – will VOID warranty.11.0 Machine Parts List – No Heater ContinuedDrawing No. Item ID Item Description Qty.50 10-0835-N Nut for Pump Bolt on Extractor 8.0051 10-0808 Caster 2.0052 10-0816 Caster Bolt 1/4-20 x 1/2 Hex Bolt 12.0053 10-0843-COM 1/2” x 54” Clear Hose for Extractor PumpIncludes Fittings and Filter1.0054 80-0040-C 46” of Blue 3000 PSI Hose for ExtractorComplete with Fittings and Clamps1.0055 80-0044-S 30” Black Hose with Fittings and Clamps 1.0056 10-0835-N Nut for Pump Bolt on Extractor 4.0057 Hose Fitting Part of 80-0044-S 1.0058 Hose Fitting Part of 80-0040-C 1.0059 80-0015 500 PSI Pump Mount Plate 1.0060 10-0833 Motor Manifold Bolts 4.0061 80-0044-L 67” Black Hose with Fittings and Clamps 1.0062 Hose Fitting Part of 80-0044-L 1.0063 Hose Fitting Part of 80-0044-S 1.0064 10-0881 1/4” MNPT x 3/8” JIC 90 DegreePart of 80-0044-S1.0065 80-0016 500 PSI Pump 1.0067 10-0400-D Keeper for Extractor Latch 1.0068 10-0832 S/R Strap Bolts 4.0069 10-0040 3000 PSI Blue Hose - Part of 80-0040-C 6.0070 80-0026 Part of 80-0040-C 1.0071 80-0017 Bulk Head fitting 3.0072 10-0379 8-32 x 3/8 Screw 8.0073 10-0400-C Latch 1.0074 10-0868 1/4” Female QD 1.0075 10-0831 S/R Bracket 2.00Not Shown 80-0200-B-3100 Extractor Wiring Harness 1.00 |
Related manuals for Sandia 80-2500
manualsdatabase
Your AI-powered manual search engine