Sansui DTV1900 Owner's Manual
Also see for DTV1300: Dimensions
    | |
1. To connect the TV to a VCR2. To connect the TV to a TV GameThe TV can also be used as a display device for many video games. However, due to the wide variety ofdifferent types of signal generated by these devices and subsequent hook-up variations required, they havenot all been included in the suggested connection diagrams. You’ll need to consult each component’s Owner’sManual for additional information.3. To connect the TV to a camcorderTo playback from the camcorder, connect the camcorder to the TV as shown.In case of “AUTO SHUT OFF” is “ON”, if a station being viewed stops broadcasting, the TV will automaticallyshut itself off after 15 minutes.Press MENU/ENTER.Press or until the indicator next to “AUTO SHUT OFF” begins to fl ash, then press or toselect ON or OFF.Press EXIT to return to the normal screen.AUTO SHUT OFFPress MENU/ENTER.1 Press MENU/ENTER.1 Press MENU/ENTER.select ON or OFF.2Press EXIT to return to the normal screen.3 Press EXIT to return to the normal screen.3 Press EXIT to return to the normal screen.You can adjust the settings for color, sharpness, contrast, brightness and tint.Press MENU/ENTER.Press or until the indicator next to “PICTURE” begins to flash, then press .Press or repeatedly to select the item you want to adjust.Press or to adjust the setting.Press EXIT to return to the normal screen.ADJUSTING PICTUREBRIGHTNESSCONTRASTCOLORTINTSHARPNESS+increase brightnessincrease contrastbe brilliant colorbe greenish colordecrease brightnessdecrease contrastbe pale colorbe reddish colormakes picture softermakes pictureclearer–Press MENU/ENTER.1 Press MENU/ENTER.1 Press MENU/ENTER.2Press3 Press3 PressPress4 Press4 PressCONTRAST COLORBRIGHTNESS TINT SHARPNESSPress EXIT to return to the normal screen.5 Press EXIT to return to the normal screen.5 Press EXIT to return to the normal screen.AUTOMATIC CHANNEL MEMORYPress MENU/ENTER.Press or until the indicator next to “CH SETUP” begins to flash,then press .Press or until the indicator next to “AUTO CH MEMORY” beginsto fl ash, then press . The TV will begin memorizing all the channels availablein your area.After fi nishing Analog Tuning, Digital Tuning starts automatically.NOTES:• It may take from 15 minutes to 30 minutes to complete memorizing digital cable channels. Depending on thereception condition, a BAR display may not advance for several minutes.• Memorizing channels is best accomplished during evening “PRIMETIME” hours, as more stations arebroadcasting digital signals. Memorizing channels can only be accomplished while a station is broadcastinga digital signal to set that channel into momory.• If you are unsure of the digital channels available in your area you may visit www.antennaweb.orgwww.antennaweb.org to receivea list based on your address or zip code. Should you require further assistance you may call our toll-freecustomer service line at 1-800-289-0980.TO ADD/DELETE CHANNELS (ANALOG MODE)Press MENU/ENTER in the analog mode.Press or until the indicator next to “CH SETUP” begins to flash,then press .Press or until the indicator next to “ADD/DELETE” begins to flash,then press .Select the desired channel to be memorized or deleted using or .Press or to select “ADD” or “DELETE”, whichever function you want to perform.Repeat steps 4 for other channels you wish to add or delete, then press MENU/ENTER.Press EXIT to return to the normal screen.TO ADD/DELETE CHANNELS (DIGITAL MODE)Press MENU/ENTER in the digital mode.Press or to select DIGITAL SETUP, then press .When DIGITAL SETUP menu appears, press or to select ADD/DELETEand press .Press or to select ADD/DELETE, then press .Select the desired channel to be memorized or deleted using or .Press or select “ADD” or “DELETE”, whichever function you want to perform.Repeat step 4 for other channels you wish to add or delete, then press MENU/ENTER.Press MENU/ENTER until the menu screen is cleared.TO ADD A DIGITAL CHANNELSelect the channel you want to add. Press or to select “ADDING CHANNEL” as in step 4 above, thenpress .Select the desired channel to be memorized or deleted using4 Select the desired channel to be memorized or deleted using4 Select the desired channel to be memorized or deleted usingRepeat steps 4 for other channels you wish to add or delete, then press MENU/ENTER.5 Repeat steps 4 for other channels you wish to add or delete, then press MENU/ENTER.5 Repeat steps 4 for other channels you wish to add or delete, then press MENU/ENTER.1Press2 Press2 PressPress3 Press3 PressPress MENU/ENTER in the digital mode.1 Press MENU/ENTER in the digital mode.1 Press MENU/ENTER in the digital mode.Press4 Press4 PressSelect the desired channel to be memorized or deleted using5 Select the desired channel to be memorized or deleted using5 Select the desired channel to be memorized or deleted usingPress2 Press2 PressWhen DIGITAL SETUP menu appears, press3 When DIGITAL SETUP menu appears, press3 When DIGITAL SETUP menu appears, pressRepeat step 4 for other channels you wish to add or delete,6 Repeat step 4 for other channels you wish to add or delete,6 Repeat step 4 for other channels you wish to add or delete,Press EXIT to return to the normal screen.6 Press EXIT to return to the normal screen.6 Press EXIT to return to the normal screen.The exact arrangement you use to interconnect various video and audio components to the TV is dependenton the model and features of each component. Check the Owner’s Manual provided with each component forthe location of video and audio inputs and outputs.The connection diagrams below are offered as suggestions. You may need to modify them to accommodateyour particular assortment of components. The diagrams are intended to show component video and audiointerconnections only.Press the TV/AV selector button to select the AV mode to use the TV as a monitor. Operate your VCR as usual.TV/AV SELECTIONIf you connect the TV to a VCR, camcorder or TV game, through the audio/video in jacks, use the TV/AV buttonto make your selection.Press the TV/AV button repeatedly to select the desired mode.“AUX” will display on the screen for 4 seconds.CONNECTION TO OTHER EQUIPMENTPress3 Press3 PressPress MENU/ENTER.1 Press MENU/ENTER.1 Press MENU/ENTER.Press2 Press2 Press7AUDIO INVIDEO INFront of TVTo AV OUTjack(not supplied)(not supplied)(not supplied)To AUDIO/VIDEOOUTFront of TVFront of TVVCRVCRAUDIO INAUDIO INVIDEO INTo AUDIO/VIDEO OUTTo AUDIO/VIDEO OUT(not supplied)(not supplied)AUDIO INAUDIO INVIDEO INFront of TVFront of TVACCESSORYRemote ControlSPECIFICATIONSAC Power Input:gAC Power Consumption:Chassis Construction:Picture Tube:Horizontal resolution:Audio Power Output Rating:Speaker:Tuner Type:Remote Control:Receiving Channels:Antenna Input Impedance:Input:Dimensions:Weight:Weight:120V, 60HzOperation: 60 WattsStand by: 3 WattsIC Solid state13" (measured diagonally)260 lines1.0 Watts3" Full Range, 8 ohmNTSC StandardATSC Standard (8VSB), QAMInfrared, Direct Access, 2 × AAA batteriesVHF 2-13UHF 14-69CATV 01-97 (5A)-(A-3)98-99 (A-2)-(A-1)14-22 (A)-( I )23-36 (J)-(W)37-65 (AA)-(FFF)66-125 (GGG)-(125)75 Ohm (VHF/UHF/CATV) Coaxial InputVideo: 1.0 Vp-p 75 ohmAudio: 300 mV, 47k ohm362 mm (W) × 360 mm (D) × 320.5 mm (H)(14-1/4" (W) × 14-3/16" (D) × 12-5/8" (H))20.9 Ibs (9.5 kg)Operation: 80 WattsStand by: 3 Watts19" (measured diagonally)488 mm (W) × 465 mm (D) × 416 mm (H)(19-3/16" (W) × 18-5/16" (D) × 16-3/8" (H))38.6 Ibs (17.5 kg)DTV1300Model DTV1900Before requesting service, please refer to the following chart for the symptom and possible solution.TROUBLESHOOTING GUIDESYMPTOMSTV does not operate.Poor sound or no sound.Poor picture or no picture.Horizontal or diagonal barson screen.• Select proper language in the menu options.No CATV reception.Picture wobbles or drifts.Poor color or no color.Poor reception on somechannels.• Make sure the power cord is plugged in.• Try another AC outlet.• Make sure the power cord is plugged in.• Try another AC outlet.• Make sure the power cord is plugged in.• Power is off, check fuse or circuit breaker.• Unplug unit for an hour, then plug it back in.• Station or CATV experiencing problems, tune to another station.• Check sound adjustments (Volume and Mute).• Station or CATV experiencing problems, tune to another station.• Check sound adjustments (Volume and Mute).• Station or CATV experiencing problems, tune to another station.• Check for sources of possible interference.• Station or CATV experiencing problems, tune to another station.• Make sure channels are set into memory.• Check antenna or CATV connections, adjust antenna.• Check for sources of possible interference.• Check picture control adjustments.• Check all CATV connections.• Set TV/CATV menu option to the CATV mode.• Station or CATV system problems, try another station.• Check antenna connections, adjust or re-direct antenna.• Check for sources of possible interference.• Batteries are weak, dead or inserted incorrectly.• Remote is out of range, move closer to TV (within 15 feet).• Make sure Remote is aimed at sensor.• Confi rm there are no obstructions between the Remote and the TV.• Make sure the power cord is plugged in.No Remote operation.TV shuts off.POSSIBLE SOLUTIONSNo reception abovechannel 13.Closed - Caption is notactivated.Display is not shown inyour language.Digital broadcasting screenproblem. • Check antenna, adjust antenna.• Station or CATV experiencing problems, tune to another station.• Make sure channels are set into memory.• Station is weak, adjust antenna to receive desired station.• Check for sources of possible interference.• Station or CATV experiencing problems, tune to another station.• Make sure channels are set into memory.• Check picture control adjustments.• Check antenna or CATV connections, adjust antenna.• Check for sources of possible interference.• Station or CATV experiencing problems, tune to another station.• Make sure channels are set into memory.• CATV company is scrambling signal.• Adjust antenna.• Make sure TV/CATV menu option is in the appropriate mode.• If using antenna, check UHF antenna connections.• No broadcast on station tuned.• Sleep Timer is set.• Power interrupted.• TV station experiencing problems or program tuned is not closed captioned.Try another channel.• Check CATV connection or VHF/UHF antenna, reposition or rotate antenna.• Press CLOSED CAPTION button to turn on the closed caption decoder.RFOR CUSTOMER SERVICE,ADDITIONAL SET-UP OROPERATING ASSISTANCEPLEASE CALL: 1-800-289-0980TO ORDER ACCESSORY PARTSOR LITERATUREPLEASE CALL: 1-888-369-0304WHEN CALLING CUSTOMER SERVICE — PLEASE HAVE YOUR MODEL NUMBER READYOR WRITE TO:ORION SALES, INC.3471 N. UNION DR.OLNEY, ILLINOIS 62450FOR INFORMATION ON OUR OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE ATwww.orionsalesinc.com |
Related manuals for Sansui DTV1300
manualsdatabase
Your AI-powered manual search engine