Sansui SLED2280 Owner's Manual

Sansui SLED2280 Owner's Manual Manual pdf 16 page image

16Starting setupThe Starting Setup menu appears the first timeyou turn on the TV, and assists you to specify theAir/Cable setting, and program your channelsautomatically.IMPORTANT: Make sure that the antenna or cableTV system connection is made!1 To turn on the TV, touch (POWER) (POWERindicator on the front of the unit changes blue.It may take approx. 10 seconds for a picture toappear on screen.). The starting setup functionbegins.Auto Setup: Adjust: SelectSignal Type CableAutomatic Search Start2 Press ◀ or ▶ to select “Cable” or “Air”.3 Press ▲ or ▼ to select “Automatic Search”, thenpress ▶ or ENTER.4 Now the “Auto Setup” starts. After the startingsetup is completed, the TV channel appears onthe screen.• Depending on the reception condition, it maytake from 15 minutes to 30 minutes to completememorizing digital cable channels. Please bepatient.NOTE:If you press ENTER in the process of “Auto Setup”,the Starting Setup stops and changes to the normalscreen.When you make a menu selection, your changesoccur immediately. You do not have to press EXIT tosee your changes.When you are finished programming the menus,press EXIT.TV operation1 To turn on the TV, touch (POWER).(POWER indicator on the front of the unitchanges blue. It may take approx. 10 seconds fora picture to appear on screen.)2 Adjust the volume level by pressing VOL + or – .The volume level will be indicated on the screenby blue bars. As the volume level increases, so dothe number of bars. If the volume decreases, thenumber of blue bars also decreases.3 Set the Signal Type option to the appropriateposition (see “Air/Cable selection” on page 19).4 Press the Direct Channel Selection (0-9, –)buttons to select the channel.(If you press only channel number, channelselection will be delayed for a few seconds.)•••TO SELECT ANALOG CHANNELS1-9: Press 1-9 as needed. Example, toselect channel 2, press 2, then pressENTER.10-99: Press the 2 digits in order. Example,to select channel 12, press 1, 2, thenpress ENTER.100-135: Press the 3 digits in order. Example, toselect channel 120, press 1, 2, 0, thenpress ENTER.TO SELECT DIGITAL CHANNELSPress the first 1-3 digits, then press the – button,followed by the remaining number.Example, to select channel 15-1, press 1, 5, –, 1,then press ENTER.If a channel is selected with only audio content,“Audio only” will be displayed on the screen.If a channel is selected with a weak digitalsignal, “Digital channel signal strength is low”will be displayed on the screen.The same program may be available on eitheran analog channel or a digital channel. You maychoose to watch either format.If a channel is selected to which you have notsubscribed, “Digital channel is encrypted” willbe displayed on the screen.•••VHF/UHF/CABLE CHANNELSAir CableVHF2-13VHF2-13UHF14-69STD/HRC/IRC14-36 (A) (W)37-59 (AA) (WW)60-85 (AAA) (ZZZ)86-94 (86) (94)95-99 (A-5) (A-1)100-135 (100) (135)01 (4A)NOTE:If a channel with no broadcast is selected, thesound will automatically be muted.It may take a few seconds for a digital channelpicture to appear on screen after being selected.To select the video input sourceTo view a signal from another device connected toyour LED TV, such as a VCR player, press INPUTSELECT, then press ▲/▼ or corresponding Numberbuttons (0-4), then press ENTER. You can select TV,Video, Component, HDMI or PC depending on whichinput jacks you used to connect your devices.Input Select[0-4]:Select0.TV1.Video2.Component3.HDMI4.PCCH /Press and release CH / . The channelautomatically stops at the next channel set intomemory.For proper operation, before selecting channels, theyshould be set into the memory. See “Memorizingchannels” on pages 19.••