Sanyo DP46812 Owner's Manual
  | |
1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance withthe manufacturer’s instructions.8. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-typeplug. A polarized plug has two blades with one wider than the other.A grounding-type plug has two blades and a third grounding prong.The wide blade or the third prong are provided for your safety. If theprovided plug does not fit fully into your outlet, consult an electricianfor replacement of the obsolete outlet.10. Protect the power cord from being walked on or pinched particu-larly at plugs, convenience receptacles, and the point where theyexit from the apparatus.11. Only use attachments/accessories specified by themanufacturer.12. Use only with the cart, stand, tripod, bracket, or table specified bythe manufacturer, or sold with the apparatus.When a cart is used, use caution when movingthe cart/apparatus combination to avoid injuryfrom tip-over.13. Unplug this apparatus during lightning stormsor when unused for long periods of time.14. Refer all servicing to qualified service personnel. Servicing isrequired when the apparatus has been damaged in any way, suchas power-supply cord or plug is damaged, liquid has been spilledor objects have fallen into the apparatus, the apparatus has beenexposed to rain or moisture, does not operate normally, or hasbeen dropped.15. If an outside antenna is connected to the television equipment, besure the antenna system is grounded so as to provide some protec-tion against voltage surges and built up static charges. In the U.S.Selection 810-21 of the National Electrical Code provides informa-tion with respect to proper grounding of the mast and supportingstructure, grounding of the lead-in wire to an antenna dischargeunit, size of grounding conductors, location of antenna dischargeunit, connection to grounding electrodes, and requirements for thegrounding electrodes.16. An outside antenna system should not be located in the vicinity ofoverhead power lines or other electrical light or power circuits, orwhere it can fall into such lines or circuits. When installing an outsideantenna system, extreme care should be taken to keep from touchingsuch power lines or circuits as contact with them might be fatal.EXAMPLE OF ANTENNA GROUNDING ACCORDINGTO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70“Note to CATV system installer:This reminder is provided to call the CATV system installer’s attentionto Article 820-40 of the NEC that provides guidelines for propergrounding and, in particular, specifies that the cable ground shall beconnected to the grounding system of the building, as close to thepoint of cable entry as practical.”17. Wall or Ceiling Mounting—The product should be mounted to awall or ceiling only as recommended by the manufacturer.18. Apparatus shall not be exposed to dripping or splashing, and noobjects filled with liquids, such as vases, shall be placed on it.19. When the MAINS plug is used as the disconnect device, the dis-connect device shall remain readily operable.RISK OF ELECTRIC SHOCK DO NOT OPEN!CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NOUSER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISKOF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTE-NANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.IMPORTANT SAFETY INSTRUCTIONSCAUTIONFCC INFORMATION ________________________________________________This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority tooperate the unit.Please read before operating your HDTV!PROTECTING THE LCDSCREENCAUTION: The screen can be damaged ifit is not maintained properly.• Do not use hard objects such as hardcloth or paper to clean the screen.• Do not use excessive pressure whencleaning the screen; excessive pressurecan cause permanent discoloration ordark spots.• NEVER spray liquids on the screen.HANDLING PRECAUTIONS• Handle by the cabinet only.• Handling by two or more people isrecommended.• Never touch the screen when handling.• Handling damage is not covered underwarranty.• Do not remove the protective filmcovering the front cabinet whilehandling the HDTV.POSITIONING THE HDTV• Always use a firm and flat surface whenpositioning your HDTV.• Do not position the unit in a confinedarea.• Allow adequate space for proper venti-lation.• Do not position the HDTV where it iseasily reachable by small children andmay present risk of injury.• Once HDTV is positioned, remove theprotective film covering front cabinet.WALL MOUNTING (OPTIONAL)NOTE: Skip these steps if using a wallmounting kit (not included).1 Place HDTV face down on apadded or cushioned flat surfaceto protect the screen and finish.2 Carefully insert the stand base tothe bottom of the HDTV and secureit by inserting four (4) screws asindicated in the diagram below.NOTE: Stand base screws are locatedin the literature package.3 Position the HDTV on a firm andflat surface with adequate spacefor proper ventilation.STAND ASSEMBLY ______GETTING STARTEDInstall two (2) “AA” batteries in theremote control. (Not included)PRECAUTIONS:• Replace both batteries at the sametime. Do not use a new battery withan old used battery.• There’s a risk of explosion if a batteryis replaced by an incorrect type.• Keep away from moisture.• Be sure to match the “+” and “–”signs on the batteries with marksinside the remote control.• Please properly dispose of used upbatteries.WARNING: The batteries (or batterypack) shall not be exposed to excessiveheat such as sunshine, fire or the like.BATTERY INSTALLATIONHook up your antenna or your cableservice to the HDTV’s ANT terminalwith the use of a 75 OHM coaxial cable.NOTE: Keep your indoor antenna atleast 3 ft. away from the televi-sion set and any other electron-ic equipment.The tuner in this HDTV can receive:• Digital and Analog off air signalsfrom an antenna• Analog or ClearQAM cable channelsfrom a direct Cable TV connection.ANTENNA CONNECTION FOROFF-AIR SIGNALS OR CABLEANTENNACABLEANALOG / DIGITALANTENNA INAV INPUT SELECTIONPress the INPUT key to select thecorrect AV input for the video sourceyou wish to watch.NOTE: Unused AV inputs may be dis-abled with the Input Setting feature.Finish Setup RepeatChannel Search Result: Succesfully CompletedIf you are having problems, call us toll-free at 1-800-877-5032Analog ChannelsVideo HDMI 1 HDMI 2Digital Channels16 26Before proceeding, please makesure to correctly hook up yourantenna or cable connection andall AV equipment to your HDTV.1. PLUG IN AC POWER CORD120V AC, 60Hz2. TURN ON TV3. TV SET LOCATION SELECTION:Select “Home Mode” to set theHDTV’s backlight to an Energy Starqualified level, or select “StoreMode” to set the backlight to a retaildisplay level.4. CHANNEL AND SIGNAL SEARCH:Select “Signal Search” and pressENTER to perform a channel searchfrom an Antenna or a direct Cableconnection, and a signal searchfrom devices hooked up to theHDTV’s AV input jacks.5. SIGNAL SEARCH RESULT SCREENThe final setup screen displays ana-log and digital channels found, aswell as AV inputs detected.SelectFinish Setup and pressENTER.NOTE: If you wish to repeat theprocess, select Repeat.INITIAL CHANNEL SEARCHNeed help? www.sanyoctv.com 1-800-877-5032 Need help? www.sanyoctv.com 1-800-877-50321JC0P1P0035 - -Part No.:© 2012 Sanyo Manufacturing Corporation1080p HDTV LCD1080p HDTV LCDOwner’sManual(English)Model No.:DP46812Sanyo Manufacturing Corp. 3333Sanyo Road, Forrest City, AR 72335This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not requirea safety connection to electrical earth.The American Academy of Pediatrics dis-courages media use by children youngerthan two years. For more information,visit www.aap.org.SPECIFICATIONSPower Requirement:Source: AC 120V, 60HzAC Power Consumption: 178 wattsWeight (w/stand) - 41 lbs.Dimensions _________________________WIDTH HEIGHT DEPTHDP46812 43.9 29.4 10.6w/out stand 43.9 26.6 4.4NOTE: Dimensions are in inchesSANYO television customersshould contact MRM Recycling at888-769-0149 or visit their websiteat www.mrmrecycling.com regar-ding SANYO’s waste manage-ment plan.CONTAINS MERCURYLAMPS, DISPOSE OFPROPERLYAs an Energy Star ® Partner,Sanyo Manufacturing Corporationhas determined that this productmeets the Energy Star ® guide-lines for energy efficiency.ENERGY STARTRADEMARKS ________Manufactured under license from DolbyLaboratories. “Dolby” is a trademark ofDolby Laboratories.HDMI, the HDMI Logo and High-DefinitionMultimedia Interface are trademarks or regis-tered trademarks of HDMI Licensing LLC inthe United States and other countries.Manufactured under license from AudysseyLaboratoriesTM. U.S. and foreign patents pend-ing. Audyssey Dynamic Volume® is a registeredtrademark of Audyssey Laboratories.ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental ProtectionAgency (EPA). ENERGY STAR is a joint program of the U.S. Environmental Protection Agencyand the U.S. Department of Energy helping us all save money and protect the environmentthrough energy efficient products and practices.Changes to default as-shipped television configuration and settings or enabling certain optionalfeatures and functionalities will change the energy consumption of the television, this mayincrease energy consumption beyond the limits required for ENERGY STAR qualification.HDTV INPUT/OUTPUT REFERENCE ________________________________________12HDMIHDMIHDTV BACK PANELHDTV SIDE PANEL3HDMI (INPUT1 or INPUT2)Use HDMI INPUT1 & 2 to hookup HD digital devices such asa Blu-ray player, HD Cable Box, HD Satellite Receiver orVideo-game System.Connect your digital device’s HDMI output to any of the two(2) HDMI inputs on your HDTV with the use of an HDMI cable.USBUSB input jack is used to connect a USB mass storagedevice to watch digital images stored in JPEG format.Digital Audio Output (Coaxial)Hookup a multichannel receiver with the use of a phono-type digital audio cable.Analog / Digital Antenna InputHook up your indoor or outdoor digital antenna, or a directCable service (Analog or ClearQAM).VIDEO INPUT (COMPONENT/COMPOSITE combo)COMPOSITE ConnectionA Composite connection is used to hookup your analogequipment such as a VCR or an older DVD player.Match the YELLOW connector from your external device tothe GREEN Y-VIDEO jack on the HDTV.NOTE: Use the WHITE and RED (L and R) jacks for AUDIOsignal.COMPONENT ConnectionA Component connection will accept SDTV, EDTV andHDTV video signals. Use it for great image quality from di-gital devices such as a DVD player or Video Game system.Match your digital device’s Component output jacks to theComponent input jack set on your HDTV.NOTE: Use the GREEN (Y), BLUE (Pb) and RED (Pr) jacks for theVIDEO signal and the WHITE and RED (L and R) jacks forthe AUDIO signal.12345Printed in Mexico, August 2012US2R / 46-Z5WPP / GXFA2This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not causeharmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.Wall mounting of the HDTV must beperformed by a skilled person.If stand base disassembly is required:• Place HDTV face down on a padded orcushioned flat surface to protect thescreen and finish.• Remove the four (4) screws securingthe foot stand. CAUTION: Hold thestand firmly as you remove the lastscrew.Use the four (4) screws included in theliterature package (or removed fromthe foot stand) to secure the HDTV to awall mounting kit.IMPORTANT: Wall mount kit mustcomply with VESA standard 400 x400. All four (4) screws must bethreaded to the wall mount andHDTV’s back cabinetMounting screws measurements:M6 (6mm) Diameter, Length—12mm(maximum)145 |
Related manuals for Sanyo DP46812
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine