T&D RTR505B User Manual
Also see for RTR505B: Read firstUser manualUser manual
Wireless Data RecorderRTR505B User’s ManualThank you for purchasing our product.To ensure safe and proper operation, please read this manualthoroughly before use.OverviewRTR505B is a data logger designed to measure and recorddifferent items depending on the input module to be con-nected: temperature (Thermocouple, Pt), analog signal(4-20mA, DC voltage), and pulse.Recorded data is then automatically collected by the Base Unit viawireless communication and downloaded for archive and analysis.As a Remote Unit, RTR505B requires a Base Unit to carry out wire-less communication.(Compatible Base Units: RTR500BC, RTR500BW, RTR-500MBS-A, RTR-500DC, RTR-500, RTR-500NW/AW)For the operation and configuration of the Base Unit, refer tothe instruction manual attached to the Base Unit or the RTR500BSeries Help available on T&D Website.Wireless Data Recorder RTR505B is referred to as the “(data) logger”or “device” in this manual.tandd.com© Copyright T&D Corporation. All rights reserved.2020.09 16508210003 (1st Edition) Printed on recycled paper.Input Modules (Sold Separately)Measurement Item Input Module LCD Displayed ItemsTemperature(Type K, J, T, S)Thermocouple Module(TCM-3010)Measurement, Unit of Measurement,Sensor Type, Operational StatusTemperature(Pt100, Pt1000)PT Module(PTM-3010)Measurement, Unit of Measurement,Sensor Type, Operational StatusVoltage Voltage Module(VIM-3010)Measurement, Unit of Measurement,Operational Status4-20mA 4-20mA Module(AIM-3010)Measurement, Unit of Measurement,Operational StatusPulse Pulse Input Cable(PIC-3150)Measurement, Unit of Measurement,Operational Status• Before using the pulse input cable, it is necessary to set the measurement item to “pulsetype” in the Remote Unit Settings of the application.• In order to change the measurement item, initialize the Remote Unit without connectingthe input module and then redo the Remote Unit registration and settings.Make sure that the module is completelyinserted until you hear a “click” sound.Installing the BatteryRecording starts automatically by inserting the battery with thedefault or previous settings.BatteryCoverRubberPackingScrewLithium BatteryDefault SettingsRecording Mode EndlessRecording Interval 10 minutesRecording StartMethodImmediate Start• Make sure to use the proper type andsize screwdriver. (Phillips head #1screwdriver is recommended.)• Insert the supplied battery with thetube attached. When using a CR2 lithi-um battery, the tube is not necessary.• Before closing the cover, check therubber packing for dust or scratches,as they can reduce the water resis-tance of the rubber.• Be sure to completely close the cover.Make sure not to over tighten thescrews.• Appropriate Tightening Torque:20N·cm to 30N·cm (2Kgf·cm to 3Kgf·cm)Battery ReplacementWhen it is time for the battery to bereplaced, a battery warning mark willappear. Please change the battery assoon as possible if this mark appears.If you continue to use the logger without changing the battery, thecurrent temperature and [bAtt] will be displayed alternately andwireless communication will stop. (Recording will continue.)AlternatingDisplay• If the battery is further left unchanged, the display will automatically shutoff and all previously recorded data will be lost.• Although the logger continues to work for a period after the battery hasbeen removed, leaving the device without a battery until the LCD displaygoes blank will cause all recorded data to be lost.Remote Unit RegistrationUsing the software of the compatible Base Unit, carry out RemoteUnit Registration via optical or Bluetooth.Optical CommunicationConnect the Base Unit to a PC with a USB cable, and place the datalogger face down to align the communication areas as shown below.Bluetooth® CommunicationWhen the RTR500BW is a Base Unit, it is possible to make Base Unitand Remote Unit settings from nearby mobile devices using Bluetooth.Package Contents• RTR505B or RTR505BL (Large Battery Type)• Lithium Battery LS14250 (or Large Capacity Battery Adaptor Kit RTR-500B1 for L type model)• Strap (Not included with L type model)• Manual Set (Warranty Included)Part NamesModule JackLCD DisplayAntennaOpticalCommunicationPort |
Related manuals for T&D RTR505B
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine