Unika S-4000 User Instructions

Contents

Unika S-4000 User Instructions Manual pdf 5 page image

Figure 2page 415. Fan Outlet Ports - Dual high speed cooling fans. Cooling air enters the amplifier throughthe front grills and exhausts through the fans. Be sure not to block these ports wheninstalling the amplifier or other associated equipment. Air must flow unimpeded throughthese ports.16. Channel 2 Balanced 1/4" TRS & XLR Input Connector - These connectors accept inputsignals on balanced TRS and XLR input plugs. Connectors for each channel are in parallel;the unused connectors may be used for "loop through" connection to other amplifiers.XLR pin setting: Pin-3/signal Negative, Pin-2/signal Positive, Pin-1/Ground.TRS pin setting: Tip/signal Positive, Ring/signal Negative, Sleeve/Ground.17. Channel 2 Frequency Adj. - This pot adjust the frequency level sent to your speaker onchannel two when using your amplifier in subwoofer mode.18. Channel 2 Subwoofer Mode On/Off Switch - Turns the subwoofer mode for channel twoon and off.19. Channel 2 XLR THRU Jack - This Jack is used to send a parallel signal from the channeltwo input jack to another device or amplifier.20. Input Gain - This sensitivity selector sets the input level for rated power output, 0.775V, 1Vor 1.44V.21. Amp. Mode Selection Switch - This switch allows the amplifier operating mode from monobridge, stereo or parallel mono selection. Amplifiers are factory-configured for StereoMode. See section on Mode Selection for more information.22. Channel 1 XLR THRU Jack - This Jack is used to send a parallel signal from the channelone input jack to another device or amplifier.23. Channel 1 Subwoofer Mode On/Off Switch - Turns the subwoofer mode for channel oneon and off.24. Channel 1 Frequency Adj. - This pot adjust the frequency level sent to your speaker onchannel one when using your amplifier in subwoofer mode.25. Channel 1 Balanced 1/4" TRS & XLR Input Connector - These connectors accept inputsignals on balanced TRS and XLR input plugs. Connectors for each channel are in parallel;the unused connectors may be used for "loop through" connection to other amplifiers.XLR pin setting: Pin-3/signal Negative, Pin-2/signal Positive, Pin-1/Ground.TRS pin setting: Tip/signal Positive, Ring/signal Negative, Sleeve/Ground.26. Reset Button - This button is designed to protect the amplifier and your speakers in theevent of an AC overload. In the event of an electrical overload, the circuit breaker will pop-out. Push it in to reset the breaker, if the breaker continues to pop, stop using the amplifierand contact customer service.27. Channel 2 Speakon Output - Use pins 1+ and 1- of this 4-pole Speakon connector toconnect to your speaker's Speakon input jack.28. Channel 1 Speakon Output - Use pins 1+ and 1- of this 4-pole Speakon connector toconnect to your speaker's Speakon input jack.29. Channel 2 Output Jack / 5-Way Binding Post - Connect to your speakers input jack. Redis positive signal and Black is negative signal.30. Channel 1 Output Jack / 5-Way Binding Post - Connect to your speakers input jack. Redis positive signal and Black is negative signal.31. AC Power Input - Plug this cable in to a standard 110V or 220V wall outlet. Be sure thatsupplied voltage matches that of the required voltage of your amplifier. Never plug youramplifier in to a wall outlet that does not match the required voltage of your amplifier,serious damage may occur to your unit.S-4000/S-5000/S-6000 REAR PANELUNiKA S-4000/S-5000/S-600015 15Introduction Front Panel Set Up Speakon Assembly Operating Modes Protection Features SpecificationsRear PanelBRIDGEMONO _ ++ +_CH-1CH-2_PINOUT1+ 1-POS NEGCH- 2PINOUT2+ 2-POS NEGCH- 21+ 2+POS NEGBRIDGE1+ 1-POS NEGCH- 1H-2CKCOLH-1CKCOLPARALLELSTEREOBRIDGETHRUPUSH TO RESETFREQUENCY20 Hz 20 Hz200 Hz 200 HzFREQUENCYCH-2 CH-1~120VAC 60HzTHRU INPUTGAININPUTNORMALSUB0.775V 1V 1.44VNORMALSUBINPUT2927 281817 2421 2220 25 263116 19 2330