Vaillant ecoTEC plus VU Series Installation And Maintenance Instructions Manual

Also see for ecoTEC plus VU Series: Installation and maintenance instructions Installation manual Installation and maintenance instructions Operating instructions Installation and maintenance instructions

Vaillant ecoTEC plus VU Series Installation And Maintenance Instructions Manual Manual pdf 44 page image

Index44 Installation and maintenance instructions ecoTEC plus 0020029173_04IndexAAir index setting................................................................... 20Air separator........................................................................ 26Air separator, filter ............................................................... 26Air/flue pipe ......................................................................... 14Air/flue pipe, installed ............................................................ 5Article number ....................................................................... 8Automatic air vent................................................................ 18BBurner anti-cycling time....................................................... 23CCalling up diagnostics codes............................................... 22Carrying out inspection work ............................................... 24Carrying out maintenance work........................................... 24CE label................................................................................. 8Check programmes ............................................................. 16Checking the burner ............................................................ 26Checking the CO₂ content ................................................... 20Checking the pre-charge pressure of the expansionvessel .................................................................................. 27Circulation pump ................................................................. 16Cleaning the condensate duct and the condensate trap..... 26Combustion air ...................................................................... 6Compact thermal module ................................................ 6, 24Completing inspection work ................................................ 27Completing maintenance work ............................................ 27Completing repair work ....................................................... 28Completing, repair work ...................................................... 28Condensate drain pipework................................................. 13Condensate duct ................................................................. 26Connecting the controller .................................................... 15Connection dimensions ......................................................... 9Corrosion............................................................................... 6Corrugated gas pipe.............................................................. 6DDecommissioning ................................................................ 28Decommissioning the product ............................................. 28Descaling the heat exchanger............................................. 25Descaling, heat exchanger.................................................. 25Diagnostics level ................................................................. 22Disposal, packaging ............................................................ 28Disposing of the packaging ................................................. 28Documents ............................................................................ 8Draining the product ............................................................ 27EElectricity ............................................................................... 5Expansion relief valve ......................................................... 13FFault codes.................................................................... 27, 34Fault memory ...................................................................... 28Filling the condensate trap .................................................. 19Filling the heating installation .............................................. 18Filling, heating installation ................................................... 18Filter, air separator .............................................................. 26Flow temperature, maximum............................................... 23Flue gas route ....................................................................... 5From the delivery point to the installation site ....................... 9Front casing, closed .............................................................. 5Frost ...................................................................................... 6GGas connection ................................................................... 12Gas ratio setting .................................................................. 19HHanding the product over to the operator............................ 23Handling ................................................................................ 9Heat exchanger ................................................................... 25Heating flow......................................................................... 13Heating partial load ............................................................. 22Heating return...................................................................... 13Hot water temperature, risk of scalding................................. 5IIdentification plate ................................................................. 8If you smell gas ..................................................................... 4Inspection and maintenance intervals ................................. 24Installation clearances......................................................... 10Installation site................................................................... 5–6Installer level ....................................................................... 22Installing the compact thermal module................................ 27Installing the front casing..................................................... 11Intended use.......................................................................... 4LLeak detection spray ............................................................. 6MMains connection ................................................................ 15Maintenance interval ........................................................... 23Minimum clearances ........................................................... 10PPerforming diagnostics........................................................ 28Power supply....................................................................... 15Preparing the repair work .................................................... 28Product dimensions............................................................... 9Pump operating mode ......................................................... 22Pump overrun...................................................................... 22Purging the heating installation ........................................... 18Purging, heating installation ................................................ 18RReading off the filling pressure............................................ 17Regulations ........................................................................... 6Removing the condensate trap ........................................... 26Replacing the burner ........................................................... 28Replacing the display .......................................................... 28Replacing the PCB .............................................................. 28Replacing, display ............................................................... 28Replacing, PCB ................................................................... 28Resetting parameters .......................................................... 28Resetting, all parameters .................................................... 28SSafety device......................................................................... 5Schematic drawing ................................................................ 5Second diagnostics level..................................................... 22Serial number ........................................................................ 8Service partner .................................................................... 27Setting the CO₂ content....................................................... 20Spare parts.......................................................................... 24Supply of combustion air ....................................................... 5Switching on the product ..................................................... 16TTool ....................................................................................... 6Transport ............................................................................... 6Treating the heating water .................................................. 17