105 SetupProcess assembly • VEGAPULS 6950714-EN-1509035 Setup5.1 SetupSetup is carried out according to the operating instructions manual ofthe respective sensor.

operating instructions

Function

For your safety 2.1 Authorised personnel

Configuration

Mounting 4.1 Mounting preparations

Mounting steps new process component

Setup 5.1 Setup

Maintenance 6.1 How to proceed if a repair is necessary

Dismount 7.1 Dismounting steps

Supplement 8.1 Technical data

Process assembly • VEGAPULS

Vega VEGAPULS 69 Operating Instructions Manual

VEGAPULS 69

Measuring principle

Type overview

Instrument selection

Selection criteria

Housing overview

Mounting

Electronics - 4 ... 20 mA/HART - two-wire

Electronics - 4 ... 20 mA/HART - four-wire

Electronics - Profibus PA

Electronics - Foundation Fieldbus

Electronics - Modbus, Levelmaster protocol

Operation

Dimensions

quick setup guide

Authorised personnel

CE conformity

Mounting 3.1 Mounting preparations, mounting strap

Connecting to power supply 4.1 Connection

Wiring plan, double chamber housing

Set up with the display and adjustment module 5.1 Insert display and adjustment module

Parameter adjustment - Extended adjustment

Supplement 6.1 Technical data

Information

Radio license for USA

Environmental instructions

Principle of operation

Packaging, transport and storage

Mounting 4.1 General instructions

Mounting versions, plastic horn antenna

Mounting preparations, mounting strap

Mounting instructions

Connecting to the bus system 5.1 Preparing the connection

Connecting

Wiring plan, single chamber housing

Double chamber housing with DISADAPT

Set up with the display and adjustment module 6.1 Insert display and adjustment module

Adjustment system

Measured value indication - Selection national language

Parameter adjustment - Quick setup

Saving the parameter adjustment data

Setup with PACTware 7.1 Connect the PC

Set up with other systems 8.1 DD adjustment programs

Diagnosis, asset management and service 9.1 Maintenance

Asset Management function

Rectify faults

Exchanging the electronics module

Software update

Dismounting steps

Technical data

Radio astronomy stations

Supplementary information Foundation Fieldbus

Industrial property rights

EU conformity

Installation and operation in the USA and Canada

Connecting to power supply 5.1 Preparing the connection

Ex-d double chamber housing

Double chamber housing with VEGADIS-Adapter

Wiring plan - version IP 66/IP 68, 1 bar

Measured value indication - Selection of national language

Saving the parameterisation data

Parameter adjustment

DD adjustment programs

Double chamber housing Ex d

Wiring plan, double chamber housing Ex d ia

Double chamber housing with DIS-ADAPT

Connecting to power supply 4.1 Connection of the battery charger

Menu overview

for your safety

product description

Connecting to the bus system 4.1 Connecting

menu overview

technical data

Radio license for Canada

Connection

Switch-on phase

Maintenance

ambient conditions

About this document

For your safety

Product description

Connecting to the bus system

Set up with the display and adjustment module

Setup with PACTware

Set up with other systems

Diagnosis, asset management and service

Dismount

Supplement

Accessories and replacement parts

Connecting to power supply

Connecting to power supply and bus system

Set up the sensor with the display and adjustment module

Setting up sensor and Modbus interface with PACTware

Set instrument address

Basics Modbus

Modbus register

Modbus RTU commands

Levelmaster commands

Configuration of typical Modbus hosts


Contents operating instructions Table Of Contents Function For your safety 2.1 Authorised personnel Configuration Mounting 4.1 Mounting preparations Mounting steps new process component Setup 5.1 Setup Maintenance 6.1 How to proceed if a repair is necessary Dismount 7.1 Dismounting steps Supplement 8.1 Technical data Process assembly • VEGAPULS	105 SetupProcess assembly • VEGAPULS 6950714-EN-1509035 Setup5.1 SetupSetup is carried out according to the operating instructions manual ofthe respective sensor. Previous Next / 16