Wali M001U Installation Manual

Wali M001U Installation Manual Manual pdf 1 page image

M001UWARNINGUSE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.If you do not understand these directions, or if you have any doubts about the safety of the installation, please call aqualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation maycause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrectassembly or inappropriate use.SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:Single Monitor Desk Mountwith Bracket AdapterVESA Platee (x1)Swivel Armd (x1)C-Clampb (x1)C-Clamp Bracec (x1)Polea (x1)Wire Clipn1 (x1)Grommet Base Platem (x1)M8x12 Boltg (x2)Nuth (x1)M5x14 Boltf (x3)M10 Bolti (x1)Support Platej (x1)M10 Washerk (x1)Spring Washerl (x1)INSTALLATION MANUAL1-844-SATTLER (18447288537)support@walielectric.comwww.walielectric.comTIPOVER WARNING● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.Supplied Parts ListWire Clipn2 (x2)M4 Spacers (x4)Wrenchp (x1)Allen Keyo (x1)M4x30 Boltr (x4)M4x12 Boltq (x4)Option A : Clamp Installation1acfoConnect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and tighten withAllen Key 3mm o .Select the preferred height according to your desk thickness. Connect C-Clamp b to C-ClampBrace c using M8x12 Bolt g and tighten with Allen Key 5mm o . Rotate the hand knobclockwise to fasten for stability.c ogba c foHand KnobcogboamfOption B : Grommet Base Installation1. Place Pole a onto Grommet Base Plate m . Connectthem from the bottom using M5x14 f Bolt and tightenwith Allen Key 3mm o .oa mfpp2a. Existing Grommet Hole Installation 2b. Self-drilled Grommet Hole InstallationIf the existing grommet hole comes with a plastic protector, remove it to ensure a flatsurface before installing the desk mount. Position the Pole a on the mounting surfaceand secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10Bolt i . Fasten the Bolt using the provided Wrench p .pj k liaMark the position of the hole on your mounting surface. Drill a 3/8" (10mm) diameter holeat the marked position through the mounting surface. Position the Pole a on the mountingsurface and secure using the Support Plate j , M10 Washer k , Spring Washer l , andM10 Bolt i . Fasten the Bolt using the provided Wrench p .aj k lpiø 10mm(ø ")3/8(x8) (x1)E(x8)DBracket(x4)Connector(x4)Cover(x4)M6X80A (x4)M6X60B (x4)M6X40C (x4)jkliajklia

/ 2

Related manuals for Wali M001U